Kronoterm WPG 30 Скачать руководство пользователя страница 52

Страница: 52 / 64

6.2018

--- ALARM DHW ----

The device was unable to heat the water higher than the min. set value
for 3 times.

ERROR Cascade:

The warning is shown if an individual device does not respond 3
x during cascade regulation verification.

-> Checking :

The device is verifying the temperature of return.

ERROR..Thermostat...
1

One of the room correctors is not connected properly or is
malfunctioning.

ERROR..Thermostat...
2

ERROR..Thermostat...
3

ERROR..Thermostat...
4

-- ALARM RTC-FAIL --

There is an error on the PLC frequency oscillator.

-- Max. ODT. / h --

The maximal limit of defrosting per hour is reached.

--MODULE 5 - ALARM--

Malfunction of one of the modules. The device will restart
automatically after the error is resolved.

--MODULE 6 - ALARM--

ERROR ..Sensor...... 14

One of the sensors is not connected or is damaged.

Carel EEV error

The Carel controller is malfunctioning.

Carel probe 1 error

One of the probes is not connected or is damaged.

Carel probe 2 error

Carel probe 3 error

Carel probe 4 error

--MODULE INV ALARM-

No connection with the external device

INV Error xx

Number of external device error.

-- Low Comp.temp --

The compressor temperature is too low. After three indications,
the PZ PROG is activated.

-- Low Cond.temp -

The plate heat exchanger temperature is too low. After three
indications, the PZ PROG is activated.

The following information is displayed in

Line 2

Description

Cooling [OFF / 22.0°C]

The device is operating in the cooling mode; set point of cooling
water is written right.

Heating [OFF / 45,0°C]

The device is operating in the heating mode; set point of heating
water is written right.

Heating FP PROG

The device is operating in the anti-freeze programme (back-up
operation) which is activated in case of alarm on the device. The
device maintains the temperature set with the parameter

Antifreeze

Passive Cooling

The device operates in the passive cooling mode.

Содержание WPG 30

































































Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды

Kronoterm WPG 30, Руководство пользователя

Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды