Kronoterm WPG 30 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 64

background image

6.2018

41

5.9 Setting the date, hour and day of the week

In case of incorrect time and date on the TERMOTRONIC controller, follow the steps below:

1.

Press key

in the basic menu.

2.

Press key

until the display shows the

following:

To change the year press key

(ENTER).

3.

The selected value 2017 starts blinking. Now
use key

or

to choose the proper value

and press key

(ENTER). Now you can

adjust the month 03, day 01, name of the day
using the same procedure as you did by setting
the year.
For returning to the basic view press the key

(MENU) twice.

5.10 Remote turn on/off

The basic regulation enables remote turn off via an external signal. Once the signal is gone the
device operates in the state before shut down.

NOTE

External turn off can be performed only in case the device was fitted with an externally
controlled switch upon installation.

5.11 PV signal

The PV signal can be turned on in the menu

mode

with the parameter

D8-PV

.

It allows factory and

user settings:

►

The factory control setting enables the control of the temperature operating mode. This

means that in the case of the winter mode (heating) you can turn on cooling. The parameter
is set to

D8-PV Cooling

. It is most often used in combination with photovoltaic systems.

►

The user control setting with parameters

D8-PV Increase 1, 2, 3 ...

enables the parameters

listed below to raise various operating modes and with it to change the temperature of the
mode:

a)  Increase 1: Comfort mode for the buffer tank.
b)  Increase 2: Comfort mode for the DHW.
c)  Increase 3: Comfort mode for the circuits.
d)  Increase 4: Comfort mode for the buffer tank and circuits.
e)  Increase 5: Comfort mode for the DHW and circuits.
f)  Increase 6: Comfort mode for the buffer tank and DHW.
g)  Increase 7: Comfort mode for the buffer tank, DHW and circuits.

Standby……………………………..
Heating……………………..35.5°C
Return

32.3°C

DHW 49.0°C

DHW

OFF

T outside

10 °C

HT60

OFF

2017/03/03

13:45 Mon

DHW

OFF

T outside

10 °C

HT60

OFF

2017/03/03

13:45 Mon

«
...
39
40
41
42
43
...
»

Содержание WPG 30

































































Отзывы:

Нет отзывов

Похожие инструкции для WPG 30

Бренд: Lasko Страницы: 4

Бренд: Calpeda Страницы: 80

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 24

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 57

Бренд: T.I.P. Страницы: 66

HYDRA-SPRAY President A Series

Бренд: Graco Страницы: 20

Бренд: XTline Страницы: 29

Бренд: Pfeiffer Vacuum Страницы: 40

BREDEL 701 Series

Бренд: Watson-Marlow Страницы: 25

Бренд: Vornado Страницы: 9

Бренд: Radiant Страницы: 40

Бренд: TapFlo Страницы: 69

Бренд: HARNITEK Страницы: 28

Бренд: CIAT Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды