background image

Read through the safety information
and overhaul instructions carefully
before repairing your Waterous HL
Series Fire Pump.

      Table of Contents

Introduction

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pump Models

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety Information

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ordering Repair Parts

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Overhaul Information

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pump Components

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly Index

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reassembly Index

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

K Series Transmission Overhaul

See F-1031, Section 4309

. . . . . . . . .

NOTE: Instructions subject to change without notice

Waterous Company, 125 Hardman Avenue South, South St. Paul, Minnesota  55075  USA  (651) 450-5000

www.waterousco.com

F-1031, Section 4321 (Rev: 

6/7/19

)

HL Series Centrifugal Fire Pumps

Overhaul Instructions

Содержание HL Series


























































Отзывы: