Waterous HL Series Скачать руководство пользователя страница 49

Страница: 49 / 57

−

1031, Section 4321

Page 49 of 57

Reassembly - Install PIV (Priming Isolation Valve)

Assemble PIV (Priming Isolation Valve)

(Required only if PIV requires overhaul)

1. Install the piston seal in the groove in the piston.

2. Install the valve seal on the piston with the pan head screw and washer.

3. Install the two (2) rod seals and O-ring in internal grooves in the valve body.

4. Install the piston in the valve body.

5. Install the wave spring from the internal bore in the valve body.

6. Install the priming valve cover with the two button head screws and

washers.

1. Install O-rings in the internal grooves in the pump body and PIV body.

2. Install priming tube in the PIV body.

3. Install PIV body/tube assembly in pump body while engaging the PIV

body on the priming tube clip.

4. Connect air line to push-on fitting retaining ring in and hold while pushing

the air line in.

Install PIV (Priming Isolation Valve)

PIV Body

PIV Body O-ring,

3/4 x 1 in.

Tube

Pump Body O-ring,

3/4 x 1 in.

Priming Tube Clip

Push-On
Fitting

PIV Body

Pan Head Screw

and Washer

Piston

Piston Seal

Priming Valve Cover

Two Button Head Screws

Rod Seals

Valve Seal

Wave Spring

Содержание HL Series


























































Результаты поиска

Содержание HL Series

Отзывы:

Бренды по названию

Популярные бренды

Waterous HL Series, Инструкции по капитальному ремонту

Результаты поиска

Содержание HL Series

Отзывы:

Бренды по названию

Популярные бренды