Waterous HL Series Скачать руководство пользователя | Manualshive

Страница: 19 / 57

background image

F

−

1031, Section 4321

Page 19 of 57

Disassembly - Remove Pump Drive End

HL200K, HL300K and HL400K Gear Drive Models

Remove Transmission:

1. Remove the four (4) bolts attaching transmission to pump.

2. Slide the transmission back until clear of shaft spline.

3. Remove the O-ring from the groove in pump pedestal.

4. If shaft will be removed from pump pedestal, remove magnetic tachometer

pick-up from pump pedestal.

NOTE: For overhaul of transmission, see separate overhaul instruction
F-1031, Section 4309.

HL200D and HL300D Direct Drive Models

Remove Companion Flange:

1. Restrain the companion flange to prevent movement.

2. Remove the locknut and washer from shaft.

3. Slide companion flange back until clear of shaft spline.

4. Remove oil seal from pump pedestal.

5. Remove spacer from shaft.

6. If shaft will be removed from pump pedestal, remove magnetic tachometer
pick-up from pump pedestal.

Two Upper Screws
and Hex Nuts

Transmission

O-ring

Magnetic Tachometer

Pick-up

Two Lower

Screws

Magnetic

Tachometer

Pick-up

Spacer

Oil Seal

Companion Flange

Washer

(Two-Pieces)

Locknut

«
...
17
18
19
20
21
...
»

Содержание HL Series


























































Отзывы:

Нет отзывов

Похожие инструкции для HL Series

Бренд: Gardena Страницы: 13

Бренд: WarmFlow Страницы: 89

Бренд: Waterous Страницы: 36

Бренд: Paragon Страницы: 16

Бренд: Samoa Страницы: 32

Бренд: Daikin Страницы: 52

Бренд: Daikin Страницы: 147

Бренд: Daikin Страницы: 175

Бренд: vacuubrand Страницы: 76

Бренд: Danfoss Страницы: 20

FLEXFLO A-100NE

Бренд: Blue-White Страницы: 28

Verderflex Vantage 5000 Series

Бренд: VERDER Страницы: 58

Бренд: K&T Страницы: 17

Бренд: Wacker Neuson Страницы: 52

Бренд: Kärcher Страницы: 50

Бренд: Macnaught Страницы: 24

Бренд: K2 Pumps Страницы: 24

Бренд: Red Jacket Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды