Kronoterm WPG 30 Скачать руководство пользователя страница 43

Страница: 43 / 64

6.2018

6 User menus and parameters

NOTE

The display of the TERMOTRONIC

controller interface shows only those menus

dependent on the type of device and were actually activated during the start-up of the
device.

6.1 Menu structure

Main menu

Parameter name

Adjustable
value

Scope [°C]

Parameter description

HEATING

C/W I

By setting this parameter, we can raise/lower
the  temperature  for  up  to  4  temperature
steps.
Example:  I>>  means  that  the  currently  set
temperature  of  the  circuit  (the  setting  in  the
parameter

Normal

)

raised

for

temperature steps.

Schedule

For settings, see chapter 5.4.

Normal

19.9

19.9…max.

The desired temperature of heating in the

Normal

mode of operation.

Eco

-2.0

-10.0…0.0

Lowering the desired temperature in the

Eco

mode of operation.

Comfort

2.0

0.0…10.0

Raising the desired temperature in the

Comfort

mode of operation.

Standby

3.0

0.0… 10.0

By  setting  this  parameter,  we  change  the
desired  temperature  of  the  restarted  device
with  the  parameter

Standby

from 0,0 °C to

10,0 °C.
Example:
The parameter

Normal

is 50,0 °C. The

device will be in standby from 47,0 °C to
50,0 °C.

Const.
temperature

Heating with constant temperature “

Const.

Temperature

”

optimised

heating

according to external temperature “

Heating

Curve

” OG. MK.

Correction

5.0

0.0…15.0

The correction of the breaking point of the
weather curve at outdoor tempe15,0
°C.

COOLING

Parameter name

Adjustable
value

Scope [°C]

Parameter description

Schedule

For settings see chapter 5.4.

Normal

19.9

10.0…19.9

The desired temperature of cooling in the
Normal mode of operation.

Eco

2.0

0.0…10.0

Raising the desired temperature in the

Eco

mode of operation.

Comfort

–

2.0

–10.0… 0.0

Lowering the desired temperature in the
Comfort mode of operation.

Standby

3.0

3.0… 10.0

By  setting  this  parameter  we  change  the
desired  temperature  of  the  restarted  device
with  the  parameter

Standby

from 0,0 °C to

10,0 °C.
Example:
The parameter Cooling is set to 23,0 °C. The
device will be in standby from 23,0 °C to
26,0 °C.

Содержание WPG 30

































































Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды

Kronoterm WPG 30, Руководство пользователя

Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды