Kronoterm WPG 30 Скачать руководство пользователя страница 50

Страница: 50 / 64

6.2018

8 Information display of operation

The controller interface TERMOTRONIC

displays information about the device on its main display

at any time. The information needed by the user is described in

Line 1

and

Line 2

The information

needed by the installer is displayed in the

DIAGNOSTICS DISPLAY

described in chapter 8.1.

NOTE

Depending on the type of installed device, the TERMOTRONIC controller display shows
various conditions of the device.

The following information is displayed in

Line 1

Description

HP STOP.............

The operation of the device is shut down (including circuit
control).

ERROR **NO
WATER*

There was a switch of the heat source pump or shortage of
water for the heat source

HpDHW

Alarm; the pressure in the cooling system was too high during heating
DHW.

HpHeat

Alarm; the pressure in the cooling system was too high during heating.

HpCool

Alarm; the pressure in the cooling system was too high during cooling.

LpDHW

Alarm; the pressure in the cooling system was too low during heating
DHW.

LpHea

Alarm; the pressure in the cooling system was too low during heating.

LpCol

Alarm; the pressure in the cooling system was too low during cooling.

Alarm; there was overvoltage, under voltage or inverted phase
sequence in the electrical grid.

DHW.................

The device heats DHW.

Screed drying.......

The programme for drying screeds is activated.

Heating.............

The device operates in the heating mode (only in winter mode).

Cooling.............

The device operates in the cooling mode (only in summer
mode).

DHW + Add.source

The device (HP – compressor) operates simultaneously with
additional heat source (the compressor and additional source
simultaneously). Switching on the additional source is described
in the section 4.6.

ScAdd.source

Heating + DHW

The device operates in the heating mode parallel to the electric
heater which is installed into the DHW for heating DHW.

H Add.source

Cooling + DHW

The device operates in the cooling mode parallel to heating of
DHW.

SwimmingPoolHeating

The device operates in the swimming pool heating mode.

Heating-Res.source..

Line 1
Line 2

Return

32.3°C

DHW

49.0°C

Содержание WPG 30

































































Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды

Kronoterm WPG 30, Руководство пользователя

Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды