Kronoterm WPG 30 Скачать руководство пользователя страница 25

Страница: 25 / 64

6.2018

5 Advanced settings

In this chapter you will find:

How to set the parameters of the device in case the system has no spatial corrector or

thermostat built in or the settings for the temperature of heating water do not suffice the
heating needs.

How to set the control mode of the heating water.
How to set the mode of operation for heating water/cooling water, heating/cooling circuits

and heating of DHW.

How to set schedules.

For easier understanding of the chapter, you can find a general scheme of the heating (cooling)
system below.

M10

M11

M12

ELEMENTS

MARK

CHARACTERISTICS

Space and DHW heating device

Heating circuits

Heating water (buffer tank)

DHW (DHW tank)

Heat consumers (floor heating / radiators)

Heat pump

Main circulation pump

Circulating pump for DHW

Circulation pump of direct heating circle 1

Circulation pump of mixing-heating circle 2

Mixing valve of mixing-heating circle 2

Circulation pump of mixing-heating circle 3

M10

Mixing valve of mixing-heating circle 3

M11

Circulation pump of mixing-heating circle 4

M12

Mixing valve of mixing-heating circle 4

NOTE

Heating circle 1 (M5) can only be a direct heating circle (without mixing valve).
For this circuit we always choose the heating circle which requires the highest
temperature (i.e. radiators).

Содержание WPG 30

































































Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды

Kronoterm WPG 30, Руководство пользователя

Результаты поиска

Содержание WPG 30

Отзывы:

Похожие инструкции для WPG 30

Бренды по названию

Популярные бренды