Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 83 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen is the second of two displays for the tem-

perature alarms and trips. Each point has either an

alarm (warning) or a trip (shutdown) or both. These

points will be configured at commissioning by a quali-

fied Johnson Controls Service Technician.

displaY onlY
discharge low Temperature

Displays the Discharge Low Temperature trip point.

discharge high Temperature

Displays the Discharge High Temperature alarm and

trip points.

Compressor oil sump Temperature

Displays the Low Oil Temperature alarm and trip points

for the oil in the compressor housing.

evaporator refrigerant low Temperature

Displays the Low Refrigerant Temperature alarm and

trip points for the evaporator.

TeMperaTure alarMs and Trips sCreen (Con'T)

TEMPERATURE ALARMS AND TRIPS SCREEN

figure 33 -

shutdown offset

This value comes in operation when the low leaving

chilled liquid temperature cutout setpoint is greater

than the difference to the minimum allowable cutout

temperature which is 36° for water or the value set for

brine.

restart offset

Temperature that will permit a restart of the chiller that

cycled off because of low leaving chilled liquid tem-

perature.

prograMMaBle

Requires access level of SERVICE,

Service Technicians refer to the Service

Instructions (Form 160.72-M1) for opera-

tion instructions and explanation of all

programmable setpoints and displayed

values.

set alarms

Allows a qualified Service Technician to change any

of the alarm points shown above. Refer to the

Service

Instructions (Form 160.72-M1)

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды