Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 24 / 138

FORM 160.72-O1 (810)

JOHNSON CONTROLS

EVAPORATOR SCREEN

to over-cooling temperature. By default, the chiller

will restart at the Leaving Chilled Liquid Temperature

Setpoint.

Chilled liquid flow switch (open / Closed)

Displays whether the liquid flow is present in the evap-

orator.

Chilled liquid pump

Displays the command presently sent by the control

center to the Chilled Liquid Pump (

RUN

STOP

evaporator low pressure

Displays the low pressure setpoint in the evaporator.

evaporator saturation Temperature

Displays the present Saturation Temperature in the

evaporator.

Chilled liquid flow

Displays the Chilled Liquid Flow, in GPM, if the sen-

sor is present.

suction refrigerant Temperature

Displays the present suction refrigerant vapor tempera-

ture leaving the evaporator. If the sensor is present and

enabled under Options on the Configuration screen.

The service access level is required to enable/disable

this display.

evaporator refrigerant Temperature

(not shown)

Displays the sensor is present refrigerant liquid tem-

perature in the evaporator. If the sensor is present and

enabled at the soft key toggle on this screen. The service

access level is required to enable/disable this display.

prograMMaBle
local leaving Chilled liquid Temperature

-setpoint

Access Level Required: OPERATOR

This value allows the user to define the Leaving

Chilled Liquid Temperature that is to be maintained by

the chiller. It is programmable over the range of 38.0°F

to 70.0°F (water) or 10.0°F to 70.0°F (brine). If Smart

Freeze (see below) is enabled, the range is 36.0°F to

70.0°F (water). A remote device can provide an analog

signal (0-20mA or 4-20mA, 0-10VDC or 2-10VDC)

in Analog Remote mode or PWM signal in Digital

Remote mode that changes the setpoint by creating

an offset above the operator programmed

Base

Leav-

ing Chilled Liquid Temperature setpoint. This offset

may be defined up to 10.0°F or 20.0°F above the

Base

setpoint (see the Remote Leaving Chilled Liquid Tem-

perature Setpoint Range description above). Addition-

ally, the E-Link gateway (in BAS Remote mode) can

define the setpoint through a serial data stream. In this

case, the incoming setpoint is not an offset that is ap-

plied to the locally programmed

Base

setpoint value,

but rather is the setpoint value itself.

local leaving Chilled liquid Temperature -

range

Access Level Required: OPERATOR

This is the range over which an analog (0-20mA or

4-20mA, 0-10VDC or 2-10VDC) in Analog Remote

Mode or a digital signal (PWM) in Digital remote

mode can reset the Leaving Chilled Liquid Tempera-

ture setpoint above the operator programmed

Base

Setpoint (see below). Programmable as either 10°F or

20°F, with a default of 20°F, it is added to the

Base

value to create a range over which the remote device

can reset the setpoint. For example, if this setpoint is

programmed for 10°F and the operator programmed

value is 45°F, then the remote device can set the Leav-

ing Chilled Liquid Temperature setpoint over the range

45.0° - 55.0°F.

leaving Chilled liquid Temperature Cycling

offset - shutdown

Access Level Required: OPERATOR

This value allows the user to specify the Leaving

Chilled Liquid Temperature at which the chiller will

shut down on a

LEAVING CHILLED LIQUID -

LOW TEMPERATURE

cycling shutdown. This is

done by defining an offset below the Leaving Chilled

Liquid Temperature setpoint. It is programmable over a

range of 1°F to 64°F below the setpoint, to a minimum

cutout of 36°F (water), 34°F (water with Smart Freeze

enabled) or 6°F (brine). It establishes the minimum al-

lowable temperature for the Leaving Chilled Liquid

Temperature and prevents over-cooling of the build-

ing. Anytime the Leaving Chilled Liquid Temperature

setpoint is increased, the shutdown threshold is 36.0°F

(water) or 6.0°F (brine) for the next ten (10) minutes.

If Smart Freeze (see below) is enabled, the threshold is

34.0°F for the next 10 minutes. After ten (10) minutes

have elapsed, the shutdown threshold becomes the pro-

grammed setpoint value.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды