Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 135 / 138

JOHNSON CONTROLS

135

FORM 160.72-O1 (810)

7. Set the Current Limit Setpoint to 100% (unless

a percentage is desired to limit maximum cur-

rent).

8. Start the chilled water pump(s) and condenser

water pump(s) and verify evaporator and con-

denser flow switches are made.

9. Reset any existing safety trips or power failures

by moving the panel switch to the STOP/RESET

(O) position and press the CLEAR MESSAGE

button on the display. If all chiller safeties are

satisfied the display will indicate READY TO

START.

10. Move the panel switch to the START (◄) posi

tion. The switch is spring-loaded and will return

to the RUN (

▐

) position when released.

11. If a building automation system (BAS) is uti-

lized to start and stop the chiller remotely via

the System Cycling or Multi-Unit Cycling con-

tacts, these contacts must be closed. A Cycling

Shutdown message will appear on the display if

the contacts are open.

The start sequence shall initiate. The display will in-

dicate the operating state of the chiller as it transitions

from start-up to run mode.

sTopping uniT

To stop the unit, proceed as follows:

1. Move the panel switch to the STOP/RESET (O)

position or open the BAS Cycling contacts.

The chiller will shut down and the post-lubrica-

tion sequence will be initiated. The display will

indicate that the unit is in COASTDOWN mode.
2. Shut down the chilled water pump(s) and con-

denser water pump(s).

3. Verify that the compressor oil sump heaters are

energized.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды