Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 117 / 138

SECTION 3 - OPTIVIEW CONTROL CENTER

JOHNSON CONTROLS

117

FORM 160.72-O1 (810)

Condenser - pressure TransduCer

ouT of range

The Condenser Pressure Transducer is indicating a

pressure that is >35.3 PSIA. This is outside the normal

operating range of the transducer. This is generally in-

dicates a defective transducer. The chiller can be start-

ed after the transducer is indicating a pressure that is <

35.3 PSIA and the

COMPRESSOR

switch is placed

in the

STOP/RESET

(O) position.

eMergenCY sTop
auxiliarY safeTY - ConTaCTs Closed

The Auxiliary Safety shutdown contacts, connected to

I/O Board TB4-31 have closed, initiating a safety shut-

down. This input is a general-purpose, user defined

safety shutdown input. The chiller can be started after

the contacts open and the

COMPRESSOR

switch is

placed in the

STOP/RESET

(O) position.

disCharge - high TeMperaTure

The discharge temperature, as sensed by the Discharge

Temperature Transmitter, has increased to > 220.0°F.

The chiller can be started after the temperature de-

creases to < 220.0°F and the

COMPRESSOR

switch

is placed in the

STOP/RESET

(O) position.

disCharge - loW TeMperaTure

The discharge temperature, as sensed by the Discharge

Temperature Transmitter, has decreased to < 30.0°F.

The chiller can be started after the temperature in-

creases to > 30.0°F and the

COMPRESSOR

switch is

placed in the

STOP/RESET

(O) position.

oil - high TeMperaTure

The oil temperature, as sensed by the Oil Temperature

Transmitter, has increased to > 180.0°F. The chiller can

be started after the temperature decreases to < 180.0°F

and the

COMPRESSOR

switch is placed in the

STOP/

RESET

(O) position.

oil - loW differenTial pressure

The differential oil pressure decreased to < 15.0 PSID

while the chiller was running or failed to achieve

20.0 PSID during the last 5 seconds of the SYSTEM

PRELUBE period. The differential oil pressure is the

difference between the output of the Sump Oil Pressure

Transducer (system low pressure) and the output of the

Pump Oil Pressure Transducer (system high pressure).

The chiller can be started after the

COMPRESSOR

switch is placed in the

STOP/RESET

(O) position.

oil - high differenTial pressure

The differential oil Pressure increased to > 60.0 PSID

while the oil pump was running. The differential oil pres-

sure is the difference between the output of the Sump Oil

Pressure Transducer (system low pressure) and the output

of the Pump Oil Pressure Transducer (system high pres-

sure). The chiller can be started after the differential oil

pressure decreases to <60.0 PSID and the

COMPRES-

SOR

switch is placed in the

STOP/RESET

(O) position.

ConTrol panel - poWer failure

A Control Power failure has occurred. If the power

failure duration was < the duration of the applicable

COASTDOWN period (2.5 minutes standard; 15 min-

utes steam turbine), the remainder of the COASTDOWN

is performed upon restoration of power. The chiller can

be started after the

COMPRESSOR

switch is placed

in the STOP/RESET (O) position. This message can

indicate a Cycling (auto-restart after power failure) or

Safety (manual restart after power failure) shutdown,

depending upon Control Center configuration. It in-

dicates a Cycling shutdown when displayed in orange

characters; Safety shutdown when displayed in red

characters. The OptiView Control center is configured

for auto-restart or manual restart after power failure by

a qualified Service Technician following instructions

in the

Service Instructions (Form 160.72-M1)

WaTChdog - sofTWare reBooT

The Microboard’s software Watchdog initiated a Micro-

processor reset because it detected that a portion of the

chiller operating Program was not being executed. The

result of this reset is a Safety shutdown and reinitialization

of the Program. This is generally indicative of a severe

electrical power disturbance or impending Microboard

Failure. The chiller can be started after the

COMPRES-

SOR

switch is placed in the

STOP/RESET

(O) position.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды