Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 23 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen displays a cutaway view of the chiller

evaporator. All setpoints relating to the evaporator side

of the chiller are maintained on this screen. Animation

of the evaporation process indicates whether the chiller

is presently in a

RUN

condition. Animation of the liq-

uid flow indicates chilled liquid flow.

displaY onlY
leaving Chilled liquid Temperature

Displays the temperature of the liquid as it leaves the

evaporator.

return Chilled liquid Temperature

Displays the temperature of the liquid as it enters the

evaporator.

small Temperature difference

Displays the difference between the Leaving Chilled

Liquid temperature and the Evaporator Refrigerant

temperature. The Evaporator Refrigerant temperature

will be represented by the Refrigerant Temperature

sensor input if the sensor is present, otherwise it will be

represented by the Evaporator Saturation temperature.

evaporaTor sCreen

EVAPORATOR SCREEN

figure 4 -

evaporator pressure

Displays the present refrigerant pressure in the evapo-

rator.

leaving Chilled liquid Temperature setpoints

- setpoint

Displays the present setpoint to which the chiller is

operating, whether controlled locally or remotely.

leaving Chilled liquid Temperature setpoints

-alarm

Displays the temperature at which a warning alarm will

be displayed on the system details message bar.

leaving Chilled liquid Temperature setpoints

-shutdown

Displays the Leaving Chilled Liquid Temperature at

which the chiller will shut down to avoid over-cooling

the building. By default this value is 4°F below the

Leaving Chilled Setpoint.

leaving Chilled liquid Temperature setpoints

-restart

Displays the Leaving Chilled Liquid Temperature at

which the chiller will restart after it has shut down due

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды