Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 37 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

These screens display a cutaway view of the Interstage

Valves. All setpoints relating to Interstage Valve control

are maintained on this screen. Also, related Interstage

Valve control parameters are displayed for reference.

Through animation, the relative valve position is dis-

played. In addition, the valve can be manually operated.

displaY onlY
interstage valve position

Displays the position of the Interstage Valve over the

range of 0% (closed) to 100% (fully open). The valve

position is animated. When the actual position is 0%

to 19%, the valve is shown fully closed. When ac-

tual position is 20% to 39% the valve is shown 25%

open. When actual position is 40% to 59%, the valve is

shown 50% open. When actual position is 60% to 79%,

the valve is shown as 75% open. Positions greater than

79 % are shown as full open.

intercooler refrigerant Temperature

Displays the present refrigerant temperature in the in-

tercooler. If the sensor is present and enabled under

Options on the Configuration screen. The service ac-

cess level is required to enable/disable this display.

inTersTage valve sCreen

INTERSTAGE VALVE SCREEN

figure 10 -

intercooler pressure

Displays the present refrigerant pressure in the inter-

cooler.

evaporator pressure

Displays the present refrigerant pressure in the evapo-

rator.

differential pressure

A parameter that represents system differential, or

HEAD. It is calculated as (Intercooler pressure –

Evaporator pressure).

liquid injection solenoid a (led)

Indicates when the Liquid Injection Solenoid is ener-

gized.

interstage valve setpoint

Displays the control point pressure the valve will oper-

ate to maintain.

pulldown Time remaining

Displays the amount of time remaining from start for

pulldown before the Interstage valve control will mod-

ulate to maintain the interstage pressure setpoint.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды