Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 89 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen displays the time alarms and trips. Each

point has either an alarm (warning) or a trip (shutdown)

or both. These points will be configured at commis-

sioning by a qualified Johnson Controls Service Tech-

nician during the manufacturing of the chiller.

displaY onlY
auxiliary oil pump overrun Time

Displays the Auxiliary Oil Pump Overrun alarm point.

auxiliary oil pump shutoff deadline

Displays the Auxiliary Oil Pump Shutoff Deadline

alarm point.

auxiliary oil pump shaft pump uptime

Displays the Auxiliary Oil Shaft Pump Uptime alarm

point.

auxiliary oil pump interlock delay

Displays the Auxiliary Oil Pump Interlock Delay trip

point, if enabled.

TiMe alarMs and Trips sCreen

TIME ALARMS AND TRIPS SCREEN

figure 36 -

Motor interlock delay

Displays the Motor Interlock Delay trip point, if en-

abled.

Motor start Contact delay

Displays the Motor Start Contact Delay trip point, if

enabled.

digital vibration enable delay

Displays the Vibration Enable Delay trip point, if en-

abled.

Chilled liquid flow start delay

Displays the Chilled Liquid Flow Switch Start Delay

trip point.

Condenser liquid flow start delay

Displays the Condenser Water Flow Switch Start De-

lay trip point.

startup alarm/Trip enable delay

Displays the time during prelube startup that alarms

will be bypassed to allow pressures to stabilize.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды