Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 87 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen is the second of two displays for the pres-

sure alarms and trips. Each point has either an alarm

(warning) or a trip (shutdown) or both. These points

will be configured at commissioning by a qualified

Johnson Controls Service Technician.

displaY onlY
low supply air pressure

Displays the Supply Air Low Pressure alarm and trip

points.

Balance piston high differential pressure

Displays the Balance Piston High Differential Pressure

alarm point.

prograMMaBle

Requires access level of SERVICE,

Service Technicians refer to the Service

Instructions (Form 160.72-M1) for opera-

tion instructions and explanation of all

programmable setpoints and displayed

values.

pressure alarMs and Trips sCreen (Con'T)

PRESSURE ALARMS AND TRIPS SCREEN (CON'T)

figure 35 -

set alarms

Allows a qualified Service Technician to change any

of the alarm points shown above. Refer to the

Service

Instructions (Form 160.72-M1)

set Trips

Allows a qualified Service Technician to change any

of the trip points shown above. Refer to the

Service

Instructions (Form 160.72-M1)

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

Temperature alarms/Trips

Access Level Required: VIEW

Moves directly to the Temperature Alarms and Trips

Screen.

Time alarms/Trips

Access Level Required: VIEW

Moves directly to the Time Alarms and Trips Screen.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды