Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 55 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen displays the pressure setpoints. These

points will be configured at commissioning by a quali-

fied Johnson Controls Service Technician.

displaY onlY
Minimum evaporator pressure for Tempera-

ture Control

This setpoint defines the minimum evaporator pres-

sure required at startup before the leaving chilled water

temperature is considered valid for temperature control

of the Pre-Rotation Vanes.

gearbox aop oh pressure

The minimum oil pressure that must be maintained

below which the Auxiliary Oil pump will be used for

gearbox supply oil.

Compressor aop oil pressure

The minimum oil pressure that must be maintained

below which the Auxiliary Oil pump will be used for

compressor supply oil.

prograMMaBle

Requires access level of SERVICE,

Service Technicians refer to the Service

Instructions (Form 160.72-M1) for opera-

tion instructions and explanation of all

programmable setpoints and displayed

values.

Change setpoints

Allows a qualified Service Technician to change any

of the setpoints shown above. Refer to the

Service In-

structions (Form 160.72-M1)

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

setup

Access Level Required: VIEW

Returns to the Setup Screen.

pressure seTpoinTs sCreen

PRESSURE SETPOINTS SCREEN

figure 19 -

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды