Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 100 / 138

FORM 160.72-O1 (810)

JOHNSON CONTROLS

100

TREND SETUP SCREEN

Select the desired

Data Collection Interval

as fol-

lows:

Determine the desired time interval (in seconds),

between data samples.
Calculate the full screen time display as follows:

450 x Data Collection Interval = full screen

•

seconds
full screen seconds/60 = full screen minutes

•

full screen minutes/60 = full screen hours

•

full screen hours/24 = full screen days

•

Decide if the resultant sample interval and full

screen display meet the requirements. If not, se-

lect a different sample interval.

select

Access Level Required: OPERATOR

This key is used to enter the slot numbers and the mini-

mum and maximum Y-axis values of each parameter

to be trended. Pressing this key places a yellow box

around Data Point 1 Slot Number. Use the

▲

and

▼

navigation keys to place the box around the value of

Data Points 1 through 6 to be changed. With the de-

sired value selected, press the

key. A dialog box is

displayed permitting data entry.

data point slot # (1-6)

Access Level Required: OPERATOR

Use the SELECT key as described above and enter

the slot number from the Common Slots Screen or

Master Slot Number List of the desired parameter to

be trended. The selected parameter description will be

displayed for the Data Point. Setting this slot number

to zero will disable trending for that particular Data

Point. Any or all points can be disabled.

data point Min (1-6)

Access Level Required: OPERATOR

Only displayed if the Associated Slot Number is not

Zero. This is the minimum value displayed for the

Y-axis. Selecting a parameter for a Data Point sets this

to the default value, which is the lowest value allowed

for that parameter. It can be changed to a value that

provides a more appropriate resolution for the param-

eter being monitored. To change, use the SELECT key

as described above and enter the desired value. The

value must always be set to a value less than the Data

Point Max. Otherwise, a red graph is displayed on the

Trend Screen with the words

TREND MAX MUST

BE > TREND MIN

. If the parameter selected for this

data point is a digital type (on/off), this value must be

set to zero (0). Zero indicates the OFF state.

data point Max (1-6)

Access Level Required: OPERATOR

Only displayed if the associated slot number is not

zero. This is the maximum value displayed for the

Y-axis. Selecting a parameter for a Data Point sets this

to the default value, which is the highest value allowed

for that parameter. It can be changed to a value that

provides a more appropriate resolution for the param-

eter being monitored. To change, use the

SELECT

key

as described above and enter the desired value. The

value must always be set to a value greater than the

Data Point Min. Otherwise, a red graph is displayed on

the Trend Screen with the words TREND MAX MUST

BE > TREND MIN. There are 20 Y-axis divisions. If a

MIN-MAX span is selected that is not evenly divided

by 20, the Program will automatically select the next

higher MAX value that makes the span evenly divided

by 20. For example, if 0.0 is selected as the MIN and

69.0 is selected as the MAX, the Program will insert

70.0 as the MAX value. If the parameter selected for

this data point is a digital type (on/off), this value must

be set to one (1). One indicates the on state.

navigaTion
home

Returns user to Home Screen.

Trending

Returns user to Trending Screen.

slot numbers

Causes a jump to a subscreen that lists the slot num-

bers of the most commonly monitored parameters. The

desired parameters to be plotted are selected from this

screen.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды