Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 40 / 138

FORM 160.72-O1 (810)

JOHNSON CONTROLS

MOTOR SCREEN

auxiliary start Contact (led)

A back-up LED that indicates when the safety contact

in the starter is closed.

length of last run

Displays the time of the last chiller run in

Day:Hr:Min:Sec format.

prograMMaBle
rated fla

Access Level Required: SERVICE

The rated FLA of the compressor motor used to de-

termine the percentage of full load amps displayed.

Service Technicians refer to the

Service Instructions

(Form 160.72-M1).

rated flKW

Access Level Required: SERVICE

The rated Full Load Kilowatts used to determine the

percentage of full load kilowatts displayed. This calcu-

lation will only be present if the Kilowatts sensor has

been enabled. Service Technicians refer to the

Service

Instructions (Form 160.72-M1)

local demand limit

Access Level Required: OPERATOR

Allows the operator to change the Demand Setpoint

from 0 % to 100 %. This will be the Current Limit

Setpoint or the Power Limit Setpoint depending on the

configuration established at commissioning. Service

Technicians refer to the

Service Instructions (Form

160.72-M1)

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

gearbox

Access Level Required: VIEW

Moves to the gearbox screen that shows temperatures

and pressures for the gearbox oil lubrication system

and allows manual control of the auxiliary oil pump,

if equipped.

anti-recycle setpoints

Access Level Required: VIEW

Moves to the anti-recycle setpoints screen that shows

timers and counters for Anti-Recycle operation.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды