Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 25 / 138

EVAPORATOR SCREEN

JOHNSON CONTROLS

FORM 160.72-O1 (810)

leaving Chilled liquid Temperature Cycling

offset - restart

Access Level Required: OPERATOR

This value allows the user to specify the Leaving Chilled

Liquid Temperature at which the chiller will restart af-

ter a shutdown on a

LEAVING CHILLED LIQUID

-LOW TEMPERATURE

cycling shutdown. This is

done by defining an offset above the Leaving Chilled

Liquid Temperature setpoint. It is programmable over a

range of 0°F to 70°F above the setpoint, to a maximum

restart value of 80°F. The chiller will automatically re-

start when this temperature is reached. This setpoint

can be used to reduce chiller cycling by delaying the

chiller restart until the cooling load has increased.

prograMMaBle
refrigerant (enabled / disabled)

Access Level Required: SERVICE

When an Evaporator Refrigerant Temperature Sensor

has been installed it must be enabled via this toggle

before the system will utilize the new, enhanced reso-

lution input. Service Technicians refer to the

Service

Instructions (Form 160.72-M1)

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды