Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 61 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen provides a convenient location for pro-

gramming the most common setpoints involved in the

chiller control.

displaY onlY
leaving Chilled liquid Temperature

Displays the present setpoint to which the chiller is

operating whether controlled remotely or locally. This

value could come from a 0-20 mA, 4-20 mA, 0-10VDC

or 2-10VDC input in Analog Remote mode, PWM sig-

nal in Digital Remote mode, remote interface in ISN

mode, or a locally programmed value.

leaving Chilled liquid Temperature Cycling –

shutdown

Displays the Leaving Chilled Liquid Temperature at

which the chiller will shut down to avoid over-cooling

the building. This value is calculated by subtracting

the Leaving Chilled Liquid Temperature Cycling Off-

set - Shutdown from the Leaving Chilled Liquid Tem-

perature - Setpoint. If this value is below the absolute

minimum allowed shutdown temperature the minimum

value is displayed.

seTup sCreen

SETUP SCREEN

figure 22 -

leaving Chilled liquid Temperature Cycling –

restart

Displays the Leaving Chilled Liquid Temperature at

which the chiller will restart after it has shut down due

to over-cooling temperature. This value is calculated

by adding the Leaving Chilled Liquid Temperature

Cycling Offset - Restart to the Leaving Chilled Liquid

Temperature - Setpoint.

prograMMaBle
local leaving Chilled liquid Temperature –

setpoint

Access Level Required: OPERATOR

This value allows the user to define the Leaving Chilled

Liquid Temperature that is to be maintained by the chiller.

It is programmable over the range of 38.0°F to 70.0°F

(water) or 10.0°F to 70.0°F (brine). If Smart Freeze (see

below) is enabled, the range is 36.0°F to 70.0°F (water).

A remote device can provide an analog signal (0-20mA

or 4-20mA, 0-10VDC or 2-10VDC) in Analog Remote

mode or PWM signal in Digital Remote mode that chang-

es the setpoint by creating an offset above the operator

programmed

Base

Leaving Chilled Liquid Temperature

setpoint. This offset may be defined up to 10.0°F or 20.0°F

above the

Base

setpoint (see the Remote Leaving Chilled

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды