Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 101 / 138

JOHNSON CONTROLS

101

FORM 160.72-O1 (810)

overvieW

This screen displays the slot numbers of the commonly

monitored parameters. The slot numbers for the re-

mainder of the available parameters are listed on the

Master Slot Numbers List that follows. From these

lists, select up to six parameters to be trended. Return

to the Trend Setup Screen and enter the parameters Slot

Numbers into Data Points 1 through 6.

Requires a login access level of OPERA-

TOR or higher.

displaY onlY
slot numbers

These are the slot numbers of the most commonly used

parameters.

prograMMaBle
page down

Access Level required: OPERATOR

Scroll down in the displayed data.

Trend CoMMon sloTs sCreen

TREND COMMON SLOTS SCREEN

figure 42 -

page up

Access Level Required: OPERATOR

Scroll up in the displayed data.

print

Access Level Required: OPERATOR

Generates a list of the slot numbers of the available

parameters.

navigaTion
home

Returns user to Home Screen.

Trend setup

Returns user to Trend Setup Screen.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды