Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 49 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen allows the manual control of the Pre-

Rotation Vanes, Hot Gas Bypass Valve, Subcooler

Valve, and Interstage Valve. Each device may be set

for automatic control or manual control between 0%

and 100%. This display also allows the setting of Anti-

Surge points and the Leaving Chilled Local Setpoint.

displaY onlY

All devices will have to following parameters that may

be viewed:

Auto calculated percentage

•

Manual percentage

•

Delta (differential) between auto and manual.

•

Control Mode

•

In addition, the Anti-Surge setpoints are also displayed.

See the Anti-Surge setpoints section for a detailed ex-

planation.

pre-rotation vanes

Displays the current PRV position.

hot gas Bypass

Displays the current Hot Gas valve position.

subcooler level

Displays the current Subcooler Liquid Level.

interstage valves

Displays the current Interstage valve position of valve

“A” or “B”.

anti-surge-high head Min. vane

Minimum vane position in percent for stable operation

at high head condition.

anti-surge-low head Min. vane

Minimum vane position in percent for stable operation

at low head condition.

anti-surge-pressure delta

Condenser pressure minus Evaporator pressure.

anti-surge Max.pressure delta

Maximum compressor differential pressure in PSID

for stable operation.

auTo / Manual ConTrol sCreen

AUTO / MANUAL CONTROL SCREEN

figure 16 -

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды