Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 21 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen gives a general overview of common chill-

er parameters for both shells.

displaY onlY
discharge Temperature

Displays the temperature of the refrigerant in its gas-

eous state at discharge of the compressor as it travels

to the condenser.

Condenser liquid Temperature - leaving

Displays the temperature of the liquid as it leaves the

condenser.

Condenser liquid Temperature - return

Displays the temperature of the liquid as it enters the

condenser.

Condenser pressure

Displays the refrigerant pressure in the condenser.

Condenser saturation

Displays the present saturation temperature in the con-

denser.

Chilled liquid Temperature - leaving

Displays the temperature of the liquid as it leaves the

evaporator.

Chilled liquid Temperature - return

Displays the temperature of the liquid as it enters the

evaporator.

Chilled liquid Temperature - setpoint

Displays the active temperature setpoint to which the

chiller is controlling the evaporator liquid. This value

could come from a 0-20mA or 4-20mA, 0-10VDC or

2-10VDC input in Analog Remote mode, PWM signal

in Digital Remote mode, E-Link gateway interface in

the BAS mode or a locally programmed value in local

mode.

evaporator pressure

Displays the present refrigerant pressure in the evapo-

rator.

evaporator saturation

Displays the present saturation temperature in the

evaporator.

sYsTeM sCreen

SySTEM SCREEN

figure 3 -

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды