Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 11 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

seCTion 3 - opTivieW ConTrol CenTer

inTroduCTion

The Optiview™ Control Center is a microprocessor

based control system for R-22 or R134a centrifugal

chillers. It controls the leaving chilled liquid tempera-

ture via pre-rotation vane controls and has the ability

to limit motor current via control of the pre-rotation

vanes. It is compatible with Electro-mechanical starter

applications.
The panel comes configured with a full screen LCD

Graphic Display mounted in the middle of a keypad

interface. The graphic display allows the presentation

of several operating parameters at once. In addition,

the operator may view a graphical representation of the

historical operation of the chiller as well as the present

operation. For the novice user, the locations of various

chiller parameters are clearly and intuitively marked.

Instructions for specific operations are provided on

many of the screens.
The graphic display also allows information to be rep-

resented in both English (temperatures in °F and pres-

sures in PSIG) and Metric (temperatures in °C and

pressures in kPa) mode.
The Control Center continually monitors the system op-

eration and records the cause of any shutdowns (Safe-

ty, Cycling or Normal). This information is recorded in

memory and is preserved even through a power failure

condition. The user may recall it for viewing at any

time. During operation, the user is continually advised

of the operating conditions by various status and warn-

ing messages. In addition, it may be configured to no-

tify the user of certain conditions via alarms.
There are certain screens, displayed values, program-

mable setpoints and manual control shown in this man-

ual that are for Service Technician use only. They are

only displayed when logged in at

SERVICE

access

level or higher. The setpoints and parameters displayed

on these screens are explained in detail in the

Service

Instructions (Form 160.72-M1)

These parameters

affect chiller operation and should NEVER be

modified by anyone other than a qualified Service

Technician. They are shown in this manual for ref-

erence only.

Advanced Diagnostics and troubleshooting informa-

tion for Service Technicians are included in the

Service

Instructions (Form 160.72-M1).

Also included in the

service manual are detailed descriptions of chiller fea-

tures, such as the Hot Gas Bypass Control, Interstage

Valve control, PID Tuning control, Remote Setpoints,

and Input/Output Sensor tuning.
The control center expands the capabilities of remote

control and communications. By providing a common

networking protocol through the Building Automation

System (BAS), YORK Chillers not only work well in-

dividually, but also as a team. This new protocol al-

lows increased remote control of the chiller, as well

as 24-hour performance monitoring via a remote site.

In addition, compatibility is maintained with the pres-

ent network of BAS communications. The chiller also

maintains the standard digital remote capabilities as

well. Both of these remote control capabilities allow

for the standard Energy Management System (EMS)

interface:

Remote Start

•

Remote Stop

•

Remote Leaving Chilled Liquid Temperature

•

Setpoint adjustment (0-10VDC, 2-10VDC,

0-20mA or 4-20mA) or Pulse Width Modulation
Remote Current Limit Setpoint adjustment

•

(0-l0VDC, 2-10VDC, 0-20mA or 4-20mA) or

Pulse Width Modulation
Remote “Ready to Start” Contacts

•

Safety Shutdown Contacts

•

Cycling Shutdown Contacts

•

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды