Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 64 / 138

FORM 160.72-O1 (810)

JOHNSON CONTROLS

CONFIGURATION SCREEN

12/24 hr

Access Level Required: OPERATOR

Allows the user to specify the format in which the time

will be presented to the user. This setpoint will affect

the display of the time on the chiller panel and on all

reports generated. 12-Hour time format will include the

and

modifiers and show the range of time be-

tween 1:00 and 12:59, while the 24-Hour time format

will show the range of time between 0:00 and 23:59.

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

setup

Access Level Required: OPERATOR

Moves to the Setup Screen.

user

Access Level Required: OPERATOR

Moves to the User Screen.

Comms

Access Level Required: OPERATOR

Moves to the Comms Screen.

printer

Access Level Required: OPERATOR

Moves to the Printer Screen.

sales order

Access Level Required: OPERATOR

Moves to the Sales Order Screen.

operations

Access Level Required: OPERATOR

Moves to the Operations Screen.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды