Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 39 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen displays all information pertaining to an

Electro-Mechanical Starter. The demand limit setpoint

may be changed from this screen. This screen also

serves as a gateway to subscreen for the Gearbox.

displaY onlY
Blind end Bearing Temperature

Displays the motor blind end bearing temperature, if

the sensor is enabled.

shaft end Bearing Temperature

Displays the motor shaft end bearing temperature, if

the sensor is enabled.

% full load amps

Displays the motor current as a percentage of the Full

Load Amps (FLA) value. For the Electro-Mechanical

Starter this is the data returned by the CM-2 board.

Current limit setpoint

Displays the current limit value in use. This value could

come from a 0-20mA, 4-20mA, 0-l0VDC or 2-10VDC

input in Analog Remote mode, PWM signal in Digital

MoTor sCreen

MOTOR SCREEN

figure 11 -

Remote mode, E-Link gateway interface in BAS mode,

or a locally programmed value.

Kilowatts

Displays the motor kilowatts, if the sensor is enabled.

% full load Kilowatts.

Displays the motor kilowatts as a percentage of the Full

Load Kilowatts (FLKW) value, if available.

power limit setpoint

Displays the power limit value in use if the chiller is

configured to use KW for demand limit.

Motor run (led)

Indicates whether the digital output from the controls is

commanding the motor to

RUN

Time since last shutdown

Displays the time since the last chiller shutdown in

Day:Hr:Min:Sec format.

interlock (led)

Indicates when the safety contact in the starter is

closed.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды