Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 38 / 138

FORM 160.72-O1 (810)

JOHNSON CONTROLS

INTERSTAGE VALVE SCREEN

interstage valve Control Mode

Indicates whether the Interstage Valve is under auto-

matic or manual control.

prograMMaBle

Requires access level of SERVICE.

Service Technicians refer to the Service

Instructions (Form 160.72-M1) for opera-

tion instructions and explanation of all

programmable setpoints and displayed

values.

[interstage valve Control] raise (Manual)

Access Level Required: SERVICE

This key allows the Service Technician to open the

valve in increments of 1% or more from its current po-

sition.

[interstage valve Control] lower (Manual)

Access Level Required: SERVICE

This key allows the Service Technician to close the

valve in increments of 1% or more from its current po-

sition.

[interstage valve Control] set (Manual)

Access Level Required: SERVICE

This key allows the Service Technician to input a value

from 0 to 100 % to position the valve immediately.

[interstage valve Control] switch to Manual

Access Level Required: SERVICE

This key toggles between Switch to Manual and

Switch to Auto to allow for control of the Hot Gas By-

pass Valve. The Interstage Valve Control Mode display

will indicate the control mode of the valve and prevent

transfer of the mode from manual to auto when the cal-

culated auto position and the manual position differ by

more than 5%. This will be indicated by the SWITCH

TO AUTO button color changing from green to red

mode from manual to auto when the calculated auto

position and the manual position differ by more than

5%. This will be indicated by the SWITCH TO AUTO

button color changing from green to red.

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

Compressor

Access Level Required: VIEW

Returns user to the Compressor Screen.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды