Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 63 / 138

JOHNSON CONTROLS

FORM 160.72-O1 (810)

overvieW

This screen is the top level of the general configura-

tion parameters. It allows programming of the time and

date, along with specifications as to how the time will

be displayed (12 or 24 hour format). In addition, the

chiller configuration, as determined by the state of the

Microboard Program Jumpers and Program Switches

is displayed. A qualified Service Technician, following

instructions in the

Service Instructions (Form 160.72-

M1)

, establishes this configuration per the desired op-

eration. This screen also serves as a gateway to more

subscreens for defining general system parameters.

prograMMaBle
present date

Access Level Required: OPERATOR

Allows the user to specify the present date. This val-

ue is critical to logging system shutdowns accurately.

When prompted to enter a date value, the user must

enter the day, month and four digit year (using leading

zeroes as necessary). If within range, the value will be

accepted. If out of range, the user is prompted for the

information again. At this point the user may retry the

date entry or cancel the programming attempt.

ConfiguraTion sCreen

CONFIGURATION SCREEN

figure 23 -

present Time

Access Level Required: OPERATOR

Allows the user to specify the present time. This val-

ue is critical to logging system shutdowns accurately.

When prompted to enter a time value, the user must

enter the hour and minute desired (using leading zeroes

as necessary). If the chiller is presently set to 24-hour

mode, the time must be entered in the 24-hour format.

Otherwise, the user must also select AM or PM for the

entered time. If out of range, the user is prompted for

the information again. At this point the user may retry

the time entry or cancel the programming attempt.

Clock (enabled / disabled)

Access Level Required: OPERATOR

Allows the user to enable or disable the real-time clock

in order to conserve battery life. The clock will be dis-

abled during manufacturing and must be enabled at

system commissioning. In addition, when preparing

for prolonged shutdown the clock should once again

be disabled.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды