Johnson Controls YORK OM Titan Скачать руководство пользователя

Страница: 28 / 138

FORM 160.72-O1 (810)

JOHNSON CONTROLS

CONDENSER SCREEN

Displays the difference between the Condenser Refrig-

erant Temperature and Subcooled Refrigerant Temper-

ature. If both the Condenser Refrigerant Temperature

and Subcooler Refrigerant Temperature sensors are

present and enabled.
See information above concerning

Condenser Refrig-

erant Temperature

and

Subcooler Refrigerant Tem-

perature.

The service access level is required to enable/disable

these displays

high pressure switch (open / Closed)

Displays the present position of the High Pressure

Switch. This will indicate whether a high pressure fault

is present.

Condenser liquid flow switch (open / Closed)

Indicates whether flow is present in the condenser.

Condenser liquid pump (run / off)

Indicates whether Condenser Liquid Pump is operating.

Condenser flow

Displays the Condenser Water Flow, in GPM, if the

sensor is present.

prograMMaBle
refrigerant (enabled / disabled)

Access Level Required; SERVICE

When a Condenser Refrigerant Temperature Sensor

has been installed it must be enabled via this toggle

before the system will utilize the new, enhanced reso-

lution input. Service Technicians refer to the

Service

Instructions (Form 160.72-M1).

navigaTion
home

Access Level Required: VIEW

Returns user to Home Screen.

refrigerant level Control

Access Level Required; SERVICE

Moves to the sub-screen allowing programming of the

Refrigerant Level Control setpoints.

Содержание YORK OM Titan











































































































































Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды

Johnson Controls YORK OM Titan, Руководство по эксплуатации

Результаты поиска

Содержание YORK OM Titan

Отзывы:

Похожие инструкции для YORK OM Titan

Бренды по названию

Популярные бренды