J&E Hall Fridgewatch 2100 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 152

background image

Fridgewatch 2100 Controller Mk4

Publication 3-58

Section 3

Page 82 of 152

Issue 1.1 : 01/08

Cause:

The pressure of the refrigerant vapour in the discharge line has exceeded
the HP cut-out setting.

Remarks:

The Home Page indicates which compressor has tripped. Check the
refrigeration system as described in the plant instruction manual.

E7

Low Oil Differential Pressure (ODP): Trip, Compressor Healthy
Off, Manual Reset

This event code is implemented for all applications

Cause:

Adequate oil differential pressure ODPS, measured between lubricating
oil pressure and suction pressure, was not established within S52
seconds after Fridgewatch 2100 received a ‘compressor running’ signal,
or the differential pressure fell below the required value during operation.

Remarks:

The Home Page indicates which compressor has tripped. Check the oil
system as described in the plant instruction manual.

E8

Compressor Failed To Unload: Trip, Compressor Healthy Off,
Manual Reset

This event code is implemented for all applications.

Cause:

The Fridgewatch 2100 Controller has tried and failed to return the
compressor slide valves to minimum load, i.e. the minimum position
switch contacts are open.

Remarks:

The Home Page indicates which compressor has tripped. Check the
compressor capacity control system:

•

Unload speed control throttle valve set incorrectly - refer to

the plant instruction manual.

•

Faulty capacity control solenoid valve(s).

•

Faulty or incorrectly set minimum slide valve position switch;

refer to the HallScrew Operators Manual in Section 2 of the
plant instruction manual.

•

Capacity control valve incorrectly specified for the tripped

compressor in configuration setting S62, S107 or S108.

E9

Compressor Failed to Start: Trip, Compressor Healthy Off,
Manual Reset

This event code is implemented for all applications.

Cause:

When the compressor motor starts, a ‘running’ signal, indicating that the
motor is operating, must be supplied to Fridgewatch 2100 before S51
Compressor Start Time expires.

Remarks:

The Home Page indicates which compressor has tripped. Check the
compressor or auxiliaries motor starter operation, and running interlocks
(as appropriate).

«
...
80
81
82
83
84
...
»

Содержание Fridgewatch 2100

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fridgewatch 2100

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: Gantner Страницы: 56

Бренд: Hamworthy Страницы: 10

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: Baby Trend Страницы: 10

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: Watlow Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды