J&E Hall Fridgewatch 2100 Скачать руководство пользователя страница 5

Страница: 5 / 152

Fridgewatch 2100 Controller Mk4

Section 3

Publication 3-58

Issue 1.1 : 01/08

Page 5 of 152

6.5.3.

Wiring Connections to Electronic Cards.......................................................................... 39

6.5.4.

Jumper Connections on Electronic Cards ....................................................................... 39

6.6.

Fridgewatch Highway Connections...................................................................................... 41

6.7.

Summary of Master/Slave Connections............................................................................... 42

Cards and Wiring Connections ................................................................................45

7.1.

FCPS1 Power Supply Card.................................................................................................. 45

7.2.

3SCOP1 Relay Outputs Card .............................................................................................. 46

User Interface ..........................................................................................................62

8.1.

Home Page........................................................................................................................... 62

8.1.1.

Event Codes .................................................................................................................... 62

8.2.

Contents ............................................................................................................................... 64

8.3.

Measured Points................................................................................................................... 64

8.4.

Operator Settings and Configuration Settings ..................................................................... 64

8.5.

Mode Selection..................................................................................................................... 64

8.6.

Information............................................................................................................................ 64

8.7.

Status Indicators................................................................................................................... 65

8.7.1.

Micro Ok........................................................................................................................... 65

8.7.2.

Trip ................................................................................................................................... 65

8.8.

Operator Input Buttons ......................................................................................................... 65

8.8.1.

Acknowledge.................................................................................................................... 65

8.8.2.

Configuration Settings ..................................................................................................... 66

8.8.3.

Home Page ...................................................................................................................... 66

8.8.4.

Previous Menu ................................................................................................................. 66

8.8.5.

Stop Compressor(s) (All Modes) ..................................................................................... 66

8.8.6.

Enter................................................................................................................................. 66

8.8.7.

Scroll Up - Raise Setting - Start/Load Compressor (Manual Control Only).................... 67

8.8.8.

Lower Setting – Unload Compressor (Manual Control Only).......................................... 68

8.9.

Supervisor Keyswitch ........................................................................................................... 68

Commissioning ........................................................................................................70

9.1.

Authority to Use the Supervisor Key .................................................................................... 70

9.2.

Checks to be Made Prior to Supplying Power to Fridgewatch 2000 ................................... 70

9.3.

Transducer Calibration and Potentiometer Adjustment....................................................... 71

9.4.

Inputting Configuration and Operator Settings During Commissioning,
Operating Mode for the First Start........................................................................................ 71

9.4.1.

Inputting Configuration Settings During Commissioning................................................. 71

9.4.2.

Inputting Operator Settings During Commissioning ........................................................ 74

9.4.3.

Operating Mode for the First Start ................................................................................... 74

9.5.

Changing Operator Settings after Commissioning .............................................................. 74

9.6.

Changing Configuration Settings after Commissioning ....................................................... 74

9.7.

Changing the Operating Mode ............................................................................................. 76

9.8.

Checking the Software Version Number.............................................................................. 76

9.9.

Printing or Downloading the Settings List ............................................................................ 77

10.

Event Codes ............................................................................................................78

10.1.

Information Only Events ....................................................................................................... 78

10.2.

Trip Events............................................................................................................................ 78

10.2.1.

Compressor Healthy ‘Off’................................................................................................. 78

10.3.

Event Codes Description...................................................................................................... 80

11.

Settings ...................................................................................................................87

11.1.

Operator Settings S1/S39 .................................................................................................... 87

11.2.

Configuration Settings S41/109 ........................................................................................... 98

12.

Maintenance ..........................................................................................................122

12.1.

Calibration of Pressure Transducers.................................................................................. 122

12.2.

Calibration of Temperature Transducers ........................................................................... 123

Содержание Fridgewatch 2100

























































































































































Результаты поиска

Содержание Fridgewatch 2100

Отзывы:

Похожие инструкции для Fridgewatch 2100

Бренды по названию

Популярные бренды

J&E Hall Fridgewatch 2100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Fridgewatch 2100

Отзывы:

Похожие инструкции для Fridgewatch 2100

Бренды по названию

Популярные бренды