J&E Hall Fridgewatch 2100 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 152

background image

Fridgewatch 2100 Controller Mk4

Section 3

Publication 3-58

Issue 1.1 : 01/08

Page 65 of 152

This page provides further details of current trips and a history of past
trips.

The processor internal clock current date and time can be displayed from
this page. Update the internal clock using configuration settings S75 to
S81.

8.7. Status

Indicators

There are two status indicators; refer to Fig 3 Display Details.

8.7.1. Micro

Ok

☺

MICRO OK

With power supplied to the Fridgewatch 2100 Controller and the main
isolator turned to the ‘on’ position, MICRO OK should be illuminated. If
the indicator extinguishes, this indicates a microprocessor fault which
cannot be corrected by the Watchdog.

8.7.2. Trip

TRIP

‘Flashes’ to indicate a trip event. Once the trip has been accepted by
pressing the

ACKNOWLEDGE button, TRIP changes from ‘flashing’ to

steady illumination and the local audible alarm is silenced. Identify and
rectify the cause of the trip before pressing the

ACKNOWLEDGE

button a second time to extinguish the

TRIP indicator and clear the

event code from the Home page display.

8.8.

Operator Input Buttons

There are ten input buttons located below the display; refer to Fig 3
Display Details.

When allocating processor time, the Fridgewatch 2100 Controller always
gives first priority to controlling and monitoring the compressor, this
means that the response to pressing an Operator Input Button may not
always be instantaneous. A brief press of a button may not register, or
only register after a short delay. It is therefore recommended to hold the
button down for at least half a second until the display changes.

Operator Input Buttons are associated with the following functions, from
left to right:

8.8.1. Acknowledge

ACKNOWLEDGE

With a trip present, pressing the

ACKNOWLEDGE button once

silences the local audible alarm and changes the ‘flashing’

TRIP

indicator to steady illumination, but does not remove the trip event
indications from the Home page display.

After the cause of the trip has been determined and rectified, a further
press of this button resets the Fridgewatch 2100 Controller, i.e. the

TRIP indicator extinguishes and the event code message(s) clear from
the Home page display.

«
...
63
64
65
66
67
...
»

Содержание Fridgewatch 2100

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fridgewatch 2100

Бренд: Nelson Страницы: 19

Бренд: C-TEC Страницы: 2

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

Бренд: Dantel Страницы: 6

GAMMA VERSUS Series

Бренд: JCM Страницы: 111

767-4804/000-800

Бренд: WAGO Страницы: 80

Бренд: Petique Страницы: 44

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

iSteam 2.0 Control

Бренд: mr. steam Страницы: 16

Бренд: Sygonix Страницы: 12

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

Бренд: Roger Страницы: 21

Бренд: HEROSE Страницы: 92

Бренд: Osaka Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды