J&E Hall Fridgewatch 2100 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 152

background image

Fridgewatch 2100 Controller Mk4

Publication 3-58

Section 3

Page 84 of 152

Issue 1.1 : 01/08

Cause:

The parameter monitored by the cut-out connected to terminals x11/x12
has exceeded the cut-out setting, causing the contacts to open.

Remarks:

The Home Page indicates which compressor has tripped. If no cut-out is
fitted, link terminals 111/112 on the 3MIO1 card, 211/212 and 311/312 on
the 3MIO2 card.

E25 to E29 Not Used

E30 Auxiliaries Failed to Start: Trip, Compressor Healthy Off,

Manual Reset

This event code is implemented for all applications.

Cause:

When Fridgewatch 2100 sends a start signal to the auxiliaries starter, a
‘running’ signal must be returned to Fridgewatch within the limit set by
S50 Auxiliaries Start Time.

Remarks:

Check the auxiliaries starter operation and running interlocks.

E31 and E32 Not used

E33 Compressor Lost Running Signal: Trip, Compressor Healthy

Off, Manual Reset

This event code is implemented for all applications.

Cause 1:

The compressor provides Fridgewatch 2100 with a running signal to
indicate that it is operating. If the running signal disappears, other than
when Fridgewatch signals the compressor to stop, Fridgewatch stops the
compressor.

Remarks:

Check the compressor starter operation and running interlocks.

Cause 2:

A fleeting break for a fraction of a second occurred in the trip interlock
chain (HP, LP and LT cut-outs, oil high temperature and compressor high
discharge temperature thermistor relays). It should be noted that this is
an extremely unlikely fault condition.

Remarks:

Check all wiring, external and internal to the Fridgewatch 2100,
associated with the trip interlock circuit. Also check the mechanical
operation of the HP, LP and LT cut-outs and thermistor relays.

E34 Auxiliaries Lost Running Signal: Trip, Compressor Healthy

Off, Manual Reset

This event code is implemented for all applications.

Cause:

The auxiliaries provides Fridgewatch 2100 with a running signal to
indicate that it is operating. If the running signal disappears, other than
when Fridgewatch signals the auxiliaries to stop, Fridgewatch stops the
compressor.

«
...
82
83
84
85
86
...
»

Содержание Fridgewatch 2100

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fridgewatch 2100

Бренд: KEENZ Страницы: 24

Бренд: Value Point Страницы: 7

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 22

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: Nacon Страницы: 24

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: IBA Страницы: 29

Бренд: FEAS Страницы: 4

Бренд: Automated Logic Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды