J&E Hall Fridgewatch 2100 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 152

background image

Fridgewatch 2100 Controller Mk4

Section 3

Publication 3-58

Issue 1.1 : 01/08

Page 101 of 152

S53 Enhancement factor for compressor 1

When the Fridgewatch 2100 is required to control compressors of
different capacities, this scaling factor ensures that the output from the
control algorithm provides a similar response regardless of which
compressor is being controlled. The scaling factor for compressor 1 is
obtained by dividing the swept volume of this compressor by the swept
volume of the smallest compressor. If all the compressors are the same
size or if the first compressor is the smallest, the scaling factor will be 1.0.
Otherwise it will be some value greater than one. The swept volumes of
HallScrew compressors are listed in Table 11.

S54 Enhancement factor for compressor 2

Derived using the same principles as setting S53.

S55 Enhancement factor for compressor 3

Derived using the same principles as setting S53.

S56 Set hours run on compressor 1 (units: hours run x 10)

Should the battery back up fail for some reason, or it is necessary to
replace the RAMP4 Processor Card, it will be necessary to re-enter the
hours run by the compressor. Entering a zero leaves the stored hours
value unaltered.

The number to be entered is the required number of hours run divided by
10, e.g. for 1200 hours, 120 would be entered and displayed.

After a value of S56 other than zero is entered, turning the Supervisor
Key to the ‘normal’ position updates the number of hours run and
automatically clears the S56 setting ready to input a new value.

m

3

/hr HS

2116 HS

2118 HS

2120

@ 50 Hz

120

151

209

HS 2100

Series

@ 60 Hz

144

181

252

m

3

/hr HSS

3116 HSS

3118 HSS

3120

@ 50 Hz

138

171

213

HS 3100

Old Series

@ 60 Hz

165

205

255

m

3

/hr HS

3118 HSS

3120 HSS

3121 HSS

3122

@

50

Hz

175 213 250 292

HSS 3100

New Series

@

60

Hz

210 256 300 350

m

3

/hr HS

3216 HS

3218 HS

3220 HS

3221

@

50

Hz

286 343 415 469

HS 3200

Series

@

60

Hz

343 411 498 562

m

3

/hr HS

4221 HS

4222 HS

4223

@ 50 Hz

504

611

716

HS 4200

Series

@ 60 Hz

605

733

859

Table 11 Swept Volumes of HallScrew Compressors

«
...
99
100
101
102
103
...
»

Содержание Fridgewatch 2100

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fridgewatch 2100

Бренд: ABB Страницы: 2

Бренд: Zolix Instruments Страницы: 22

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

GA Industries 930-DT

Бренд: Vag Страницы: 4

Бренд: HW Group Страницы: 18

Бренд: L&L Страницы: 16

Бренд: Zencontrol Страницы: 2

Бренд: Daikin Страницы: 2

Бренд: Advantech Страницы: 3

Бренд: Phason Страницы: 8

Бренд: JANE Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды