J&E Hall Fridgewatch 2100 Скачать руководство пользователя страница 77

Страница: 77 / 152

Fridgewatch 2100 Controller Mk4

Section 3

Publication 3-58

Issue 1.1 : 01/08

Page 77 of 152

Use the navigation buttons

and

to move around the menu pages.

CONTENTS

Measured

Points

Mode

Selection

Operator

Settings

Config

Settings

Info

Press the

HOME PAGE or

PREVIOUS MENU buttons to select the Contents page.

Use the

button to select Mode Selection. Press the

ENTER button. The Mode Selection

page is displayed.

Insert the key into the Supervisor Keyswitch and turn to the Unlocked position. The presently
selected mode will ‘flash’.

List of Modes

Mode: (

current

mode

)

Start/Stop Capacity

Control

Manual

Auto

Select the new operating mode using the

and

buttons.

Turn the Supervisor Key to the Locked position to accept the new mode; an arrow

←

will indicate

the selection. Remove the Supervisor Key.

Wait for the selected mode to appear in the top line of the display.

Press the

HOME PAGE button. Note that the selected operating mode appears in the

display.

Fig 30 Changing the Operating Mode

(c)

Restart the plant in the required operating mode; refer to 9.7.
Changing the Operating Mode.

9.9. Printing

Downloading the Settings List

A list of Operator and Configuration settings values can be printed or
downloaded to a laptop PC without stopping the compressor.

(a)

Connect a printer or laptop computer to printer terminals PC and
PO on the RAMP4 Processor Card; refer to Fig 21 for connection
details.

(b)

Set S34 Printer Selected to 1; refer to 9.5. Changing Operator
Settings after Commissioning.

If there is a printer already attached to Fridgewatch 2100, S34
Printer Selected will already be set to 1.

(c)

Display Operator Settings. Turn the Supervisor Key to the
Unlocked position.

Press the button which normally prints a log. Either the

ACKNOWLEDGE button (no trips present), or the button
connected across RAMP4 card ter and 5.

(d)

If necessary, set S34 Printer Selected to 0.

Содержание Fridgewatch 2100

























































































































































Результаты поиска

Содержание Fridgewatch 2100

Отзывы:

Похожие инструкции для Fridgewatch 2100

Бренды по названию

Популярные бренды

J&E Hall Fridgewatch 2100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Fridgewatch 2100

Отзывы:

Похожие инструкции для Fridgewatch 2100

Бренды по названию

Популярные бренды