Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание

Страница: 62 / 94

Section 5 - Commissioning
COMMISSIONING
62 Installation and Maintenance
5.7.3.2 Combined Weather and Room Compensation
The deviation of the current room temperature from the
setpoint is acquired and taken into account when controlling
the room temperature. This way, consideration is given to
room temperature deviations, ensuring more accurate room
temperature control. The authority of the deviation is set as a
percentage value.
The better the reference room conditions (correct room
temperature, correct mounting location, etc.) the higher the
value can be set.
Approx. 50 % Good reference room
Approx. 20 % Unfavourable reference room
To provide the function, following must be considered:
• A Halo Air must be connected
•
"Room influence" must be set to a value between 1 and 99
• There should be no thermostatic radiator valves in the
reference room (mounting location of room sensor); if such
valves are installed, they must be fully opened
Figure 50. Weather Compensation with Room Influence (example at gradient 0.5)
40
50
60
70
-20 -15 5 -5 -10 10
-4,5
+4,5
20
0
10
30
0
30
temperature°C
External temperature °C
Heating
flow
Curve o ff -set
Heating curve
gradient
0.5
1 Time
1 Date
20 Language
40 Used as
42 Assignment device
44 Operation zone 2
46 Operation zone 3
48 Warmer/cooler device 1
516 Time program heating circuit 1
536 Time program heating circuit 2
576 Time program 4/DHW
700 Operating mode
710 Comfort temp setpoint heating circuit 1
712 Reduced temp' setpoint heating circuit 1
720 Heating curve heating circuit 1
730 Summer/winter heating limit heating circuit 1
750 Room influence heating circuit 1
790 Optimum start control max heating circuit 1
791 Optimum stop control max heating circuit 1
850 Floor curing function heating circuit 1
851 Floor curing setp manually heating circuit 1
856 Floor curing day current heating circuit 1
857 Floor curing days completed heating circuit 1
1000 Operating Mode heating circuit 2
1010 Comfort temp setpoint heating circuit 2
1012 Reduced temp' setpoint heating circuit 2
1020 Heating curve heating circuit 2
1030 Summer/winter heating limit heating circuit 2
1050 Room influence heating circuit 2
1090 Optimum start control max heating circuit 2
1091 Optimum stop control max heating circuit 2
1150 Floor curing function heating circuit 2
1151 Floor curing setp manually heating circuit 2
1156 Floor curing day current heating circuit 2
1157 Floor curing days completed heating circuit 2
1600 Operating mode DHW
1610 Nominal temperature DHW
1612 Reduced temperature DHW
1620 DHW Release
1640 Legionella Protect
2793 Pump speed max
2803 Overrun time cond pump
2843 Compressor off time min
2907 Silent mode power max
3026 Silent mode on
3027 Silent mode off
3110 Heat delivered
3113 Energy brought in
3116 Performance factor
5700 Heating circuits No & Type
5703 Outdoor unit power rating
5710 Heating circuit 1
5715 Heating circuit 2
5740 Output el imm heater K6
5806 Type el imm heater flow
5895 Backup heater
6220 Software version
6600 Device address
6601 Segment address
6800 Fault 1 Time/Date
6801 Fault Code 1
6802 Fault 2 Time/Date
6803 Fault Code 2
6804 Fault 3 Time/Date
6805 Fault Code 3
6806 Fault 4 Time/Date
6807 Fault Code 4
6808 Fault 5 Time/Date
6809 Fault Code 5
6810 Fault 6 Time/Date
6811 Fault Code 6
6812 Fault 7 Time/Date
6813 Fault Code 7
6814 Fault 8 Time/Date
6815 Fault Code 8
6816 Fault 9 Time/Date
6817 Fault Code 9
6818 Fault 10 Time/Date
6819 Fault Code 10
7070 HP Interval
7141 Emergency Mode
7150 Simulation outside temp
7202 Commissioning heat pump
7207 Outp selection HP modulating
7208 Outp selection speed Q3
7214 Output test operating point
7700 Relay Test
8006 State heat pump
8400 Compressor 1 state
8406 Condenser pump state
8407 Speed condenser pump
8410 Return temp HP 8411 Setpoint HP
8412 Flow temp HP
8411 Setpoint HP
8413 Compressor modulation
8415 Hot-gas temp 1
8425 Temp diff condensor
8434 Suction gas temp
8450 Hours run compressor 1 Reset
8458 State smart grid
8460 Primary water flow
8493 Outdoor water flow
8700 Outside temp
8703 Outside temp attenuated reset
8704 Outside temp composite
8740 Room temp 1
8743 Flow temp 1
8744 Flow temp setpoint 1
8770 Room temp 2
8773 Flow temp 2
8774 Flow temp setpoint 2
8820 Diverter valve position
8821 Immersion heater state
8830 DHW temp
8840 Hours run DHW mode reset
8842 Hours run immersion dhw Reset
5.7.4 Installer Parameters