Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание, Страница: 12 / 94

Section 2 - Product Information
PRODUCT
INFO
12 Installation and Servicing
Table 3 Data - Two Zone Pre-plumbed Cylinders with Integrated Low Loss Header
Heat Up Time, HWA Heat Pump Test 002:2020 (flow rate 0.42l/s and flow temperature of 55°C)
Heat Up Time, BS EN 12897, G3 Performance Test (flow rate of 0.25l/s / 80°C).
The relative heat up times stated are based on the tests referenced above and carried out on all cylinders within the range. The stated test value may not reflect real life
performance within a residential environment.
Figure 8. Plan View - PP Two Zone LL - 475 mm Figure 9. Plan View - PP Two Zone LL - 550 mm
1
2
3
6
7
8
9
10 Overh
eat T
herm
ostat
Con
trol T
herm
istor
CYLINDER
HOT OUTLET
4
5
CONTROL PANEL
MINIMUM
< - - CLEARANCE - - >
FOR REMOVAL
OF PTRV
ALLOW EXTRA 200MM CLEARANCE
< - - - FOR FILTER & SPANNER ACCESS
236398 A01
<- MINIMUM WIDTH = 705 mm ->
<
- M
IN
IM
UM
D
EP
TH
=
6
35
m
m
->
All pipe holes are optional.
All pipe hole sizes are dictated by the
property / design. Therefore are a general indication.
The template is a general guide for installation
rather than a rule that must be followed without
deviation.
Number
Description Size (mm)
1 Heat Pump Flow 28
2 Heat Pump Return 28
3 Central Heating Return 22/28
4 Central Heating Return 22/28
5 Central Heating Flow Z2 22/28
6 Central Heating Flow Z1 22/28
7 Tundish Outlet 22
8 Balanced Cold Feed
22/28
9
Mains Cold Supply 22/28
10 Hot Water Feed
22/28
1
2
3
6
7
8
9
10
Overh
eat T
herm
ostat
Con
trol T
herm
istor
CYLINDER
HOT OUTLET
4
5
CONTROL PANEL
MINIMUM
< - - CLEARANCE - - >
FOR REMOVAL
OF PTRV
ALLOW EXTRA 200MM CLEARANCE
< - - - FOR FILTER & SPANNER ACCESS
<- MINIMUM WIDTH = 760 mm ->
<
- M
IN
IM
UM
D
EP
TH
=
7
10
m
m
->
236398 A01
All pipe holes are optional.
All pipe hole sizes are dictated by the
property / design. Therefore are a general indication.
The template is a general guide for installation
rather than a rule that must be followed without
deviation.
Number
Description Size (mm)
1
Heat Pump Flow
28
2 Heat Pump Return 28
3
Central Heating Return
22/28
4 Central Heating Return 22/28
5
Central Heating Flow Z2
22/28
6 Central Heating Flow Z1 22/28
7 Tundish Outlet 22
8 Balanced Cold Feed 22/28
9 Mains Cold Supply 22/28
10 Hot Water Feed 22/28
Two zone Pre-plumbed Cylinders with integrated low loss header
General Description
210, 250 & 300 litre; 475mm & 550mm diameter; single coil cylinders intended for coupling with a range of heat pumps
5kW to 14kW; Pre-plumbed and pre-wired including control box. Intended for a dual zone heating system installation. A low
loss header is supplied fitted to decouple the heat pump from the heating zones.
Assembly Model code/number
Logic Air DHW pre-plumbed
slimline cylinder 210L, control
box & low loss header 2-zone
Logic Air DHW pre-plumbed
cylinder 210L, control box &
low loss header 2-zone
Logic Air DHW pre-plumbed
cylinder 250L, control box &
low loss header 2-zone
Logic Air DHW pre-plumbed
cylinder 300L, control box &
low loss header 2-zone
Assembly UIN 236205 236200 236201 236202
Cylinder model code/number IDEPLUHP210PPDZSL IDEPLUHP210PPDZ IDEPLUHP250PPDZ IDEPLUHP300PPDZ
Energy Efficiency Class C B C C
Heat Loss
Watts 65 55 63 72
kWh/24h 1.55 1.33 1.52 1.74
Capacity (DHW content) Litres 188 199 237 279
Volume heated by immersion heater Litres 184 177 227 267
Weight Empty kg 60.6 64 69.8 73.4
Weight Full kg 248.9 262.8 307 352.4
Pressure Reducing valve setting bar 3 3 3 3
Expansion relief valve setting bar 4.5 4.5 4.5 4.5
Temperature setting of TPRV °C 95 95 95 95
Pressure setting of TPRV bar 6 6 6 6
Potable Expansion Vessel size. Litres 24 24 24 35
Expansion Vessel charge bar 3 3 3 3
Overall Width mm 647 704 704 704
Overall Height mm 2042 1572 1822 2068
Overall Depth mm 620 686 686 686
Cylinder Diameter mm A 475 A 550 A 550 A 550
DHW outlet mm B 2023 B 1553 B 1803 B 2049
Cylinder Height mm C 1963 C 1494 C 1744 C 1990
TPRV port mm D 1737 D 1252 D 1502 D 1748
Manual reset overheat thermostat pocket mm E 1151 E 1051 E 1150 E 1150
Primary flow mm F 647 F 647 F 647 F 647
Secondary return port mm G 1551 G 1141 G 1353 G 1562
Thermistor pocket mm H 816 H 687 H 769 H 823
Primary return mm J 61 J 61 J 61 J 61
Immersion heater pocket mm K 230 K 230 K 230 K 230
Cold water inlet mm L 1961 L 1475 L 1726 L 1971
Cylinder Drain mm M 220 M 220 M 220 M 220
CH1 Flow mm N 266 N 266 N 266 N 266
CH2 Flow (n/a to SZ version) mm P 156 P 156 P 156 P 156
CH Return mm Q 132 Q 132 Q 132 Q 132
Buffer Connections mm R - R - R - R -
Buffer Inspection mm S - S - S - S -
Buffer Drain mm T - T - T - T -
Primary heat exchanger surface area m
2
2.5 2.5 3.0 3.0
Primary heat exchanger capacity Litres 10.6 10.6 10.6 10.6
Low Loss Header Capacity Litres 1.95 1.95 1.95 1.95
HWA Heat pump Test - - - - -
Primary heat exchanger thermal rating kW 19.9 16.1 18 19
Heat up time from 10°C to 50°C min 23.7 30.6 27.3 35.1
V40 Litres 222 227 276 317
BS EN 12897 Test - - - - -
Primary heat exchanger thermal rating kW 35.2 34.5 36 37.4
Primary heat exchanger pressure loss bar 0.05 0.05 0.04 0.05
Heat up time from 10°C to 60°C min 18.8 18.7 22.0 23.0
V40 Litres 306 303 373 406
Revision Level D8.2 D8.2 D8.2 D8.2
relates to 236205 Logic Air DHW pre-plumbed slimline cylinder 210L, control box
& low loss header 2-zone
relates to 236200 Logic Air DHW pre-plumbed cylinder 210L, control box & low
loss header 2-zone, 236201 Logic Air DHW pre-plumbed cylinder 250L, control
box & low loss header 2-zone and 236202 Logic Air DHW pre-plumbed cylinder
300L, control box & low loss header 2-zone