Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ Скачать руководство пользователя страница 28

Страница: 28 / 94

INST

ALLA

TION

Installation and Maintenance

Section 4 - Installation

4.1 INSTALLATION OF HEAT PUMP

4.1.1 Preparation of Installation Area

The installation site is to follow the requirements and be

determined using the conditions outlined in Section

3.3.

Figure 27

shows the dimensions of the mounting fixtures of

the Heat Pump.

Ideal Heating offer anti-vibration mounting feet for the Logic

Air Heat Pump which will provide both vibration protection and

the necessary minimum ground clearance requirements.

4.1.2 Floor Mounting

4.1.2.1 Mounting Foundation

A level mounting foundation must be prepared, and it is to be

structurally sound and designed to not structurally degrade

over time. It is to be of stable and solid construction following

structural engineering principles and it must easily support the

weight of the Heat Pump.
The Heat Pump must be raised to at least 5 cm above the

ground level. In areas prone to snow, this height should be

increased but should not exceed 100 cm from ground level.

ᘐ

CAUTION: To not impede the performance of the

Heat Pump it must be made sure that the foundation is

level. Failure to meet this requirement may compromise

the unit’s ability to correctly drain condensate and

negatively affect the operation of the refrigerant circuit.

4.1.2.2 Condensate Disposal into Ground

If the condensate is to be disposed of into the ground then it

is to be disposed of into an appropriate soak-away.

If the Heat Pump is to be ground-mounted above a non-

permeable surface, such as concrete, a localised condensate

disposal method is to be installed into a nearby rainwater

gully. Refer to Section

4.1.5

SCAN

for link

Figure 27. Dimensions of Mounting Fixtures (all models)

688

516

855

800

518

1095

499

815

481

041

105

AIR

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды

Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание

Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды