Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ Скачать руководство пользователя страница 27

Страница: 27 / 94

Section 3 - Pre-Installation Checks

PRE-INST

ALLA

TION

Installation and Maintenance

3.5 CONTROL BOX - INSTALLATION AREA
3.5.1 Product Dimensions and Installation Clearances

ᘐ

CAUTION: The product is not to be obstructed by any surrounding objects or surfaces as this can limit access and

adversely affect performance. The minimum clearances that are shown in

Figure 21

should be always maintained.

3.5.2 Determining Installation Area

The proposed installation site should be explained, discussed,

and agreed with the client prior to the start of installation. It

should be accessible for the specific end user for control of the

heating system.
Both power cables and communication cable routing should be

considered when selecting an installation site.

3.5.3 Requirements of Installation Area

If installing the Logic Air Pre-Plumbed (PP) cylinder with

mounted control box, refer to Section

2.3

–

2.6

for dimensions,

access, and clearance requirements.
If installing a third-party cylinder and separate control box,

refer to Section

2.4.1

for control box dimensions, access, and

clearance requirements.
Precautions should be put in place to protect the control box

from damage e.g. impact, splashing, etc.
The installation site is to be free from water, high levels of

humidity, or debris as this can cause malfunction or damage

in the control box. The installation site must not exceed the

operating temperature or humidity tolerances given in

Table 1.

The installation site must be free from the influence of

electromagnetic, electrostatic, or magnetic fields, and not be

mounted in direct sunlight.
The proposed installation site should be explained, discussed,

and agreed with the client prior to the start of installation. The

site must be accessible for the end user.
The installation site must consider the routing of power supply

electrical cables and interconnecting cables for sensors. Make

sure adequate segregation is achieved.

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды

Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание

Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды