Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ Скачать руководство пользователя страница 60

Страница: 60 / 94

Section 5 - Commissioning

COMMISSIONING

Installation and Maintenance

Press the dial.

Back

1/4

Schedule

21.0ºC

18.0ºC

700 Operating mode

710 Comfort temp setpoint

712 Reduced temp’ setpoint

Heating Circuit 1

08:32

Rotate the dial so that 1/4 is

shown

Back

1/4

Schedule

21.0ºC

18.0ºC

700 Operating mode

710 Comfort temp setpoint

712 Reduced temp’ setpoint

Heating Circuit 1

08:32

Press the dial.

Back

1/4

Schedule

21.0ºC

18.0ºC

700 Operating mode

710 Comfort temp setpoint

712 Reduced temp’ setpoint

Heating Circuit 1

08:32

Rotate the dial so that 2/4 is shown.

Back

2/4

1.50

21.0ºC

50%

720 Heating curve

730 Summer/winter heating limit

750 Room influence

Heating Circuit 1

08:32

RE-COMMISSION HEAT PUMP

Having changed the Access Level from End User to Installer, the

following screen will be shown:-

Relay Test

Simulate Out’ Temp’

Heat Pump Status

Outside Temp’

Fault History

Versions

08:32

If you would like to recommission the heat pump, rotate the dial

until the spanner symbol is highlighted and press the dial then

the following screen is shown:-

Complete parameter list

Quick Set Up

08:32

Rotate the dial until Quick Set Up is highlighted and press the

dial.

ⓘ

IMPORTANT: If the heat pump is installed with a Halo

Air, after any changes to the heat pump parameters, make

sure to press the "Override" button on the Halo Interface to

synchronise the upated parameters. If the "Override" button

is not pressed any amended parameters will not be updated

to the Halo thermostat.

HP Comms

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание, Страница: 60 / 94

Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы: