background image

Section 5 - Commissioning

COMMISSIONING

47

Installation and Maintenance

5.3  FILLING THE SYSTEM

1.  Once the circuit has been charged with water.
2. 

Make sure that all air vents have been purge around the 

system until there are no longer any bubbles. 

3.  Charge the circuit and raise the pressure between 1 to 1.5 

bar.

4.  Operate the system circulator. 
5.  Repeat steps 2 – 4 until all the air is removed from the 

system.

6. 

Close off all air vents.

 

WARNING: During charging operations, it must 

be made sure that the electrical components of the 

circuit and surrounding area have their electrical 

supply switched off or protected from potential water 

leaks/sprays. Failure to comply with this requirement 

increases the risk of electric shock, damage to the 

products. 

Make sure that all circuits connections have been made and 

drainage valves are closed before charging the system. A 

system circulator is not to be operated whilst initially charging 

the system.  
Refer to 

5.2.2

 for dosing requirements.

Filling the System

The primary heating circuit is charged using the following 

method: 
1. 

Review the circuit and confirm that installation has been 

completed. 

2.  Open automatic air vent dust cap.  Refer to 

Figure 47

.

3. 

The filing loop is to be gradually opened whilst looking at 

the pressure gauge.

4.  Fill the system to between 1 - 1.5 Bar.

5.4  SYSTEM AIR VENTING

 

CAUTION:

 Care should be taken when filling the 

system. If pressure is difficult to achieve, or if a pressure 

drop is observed after the pressure is settled, circuit 

components and routes should be reviewed and checked 

for water leaks. 

Figure 47.  Auto Air Vent Dust Cap

Auto air 

vent dust 

cap

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Отзывы: