Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ Скачать руководство пользователя страница 68

Страница: 68 / 94

RECYCLE & DISPOSE

Installation and Maintenance

Section 8 - Recycle & Disposal

8.1 PACKAGING

8.2 END OF PRODUCT LIFE

It is the responsibility of the system installer to correctly

dispose and recycle of the products packaging.

8.2.1 Environmental Protection

ᘐ

WARNING: Under no circumstance should the

refrigerant fluid be released into the atmosphere. Any

action to remove the refrigerant from the Heat Pump is to

be carried out by a competent engineer with a current Cat

III, Cat II or Cat I F-Gas certificate.

Ideal Heating strives to use renewable materials and

energy resources in our design and production processes.

Environmental protection regulations and legislation are to be

always obeyed.

8.2.2 WEEE

WEEE DIRECTIVE 2012/19/EU
Waste Electrical and Electronic Equipment

Directive

•

At the end of the product life, dispose of the packaging and

product in a corresponding recycle centre.

•  Do not dispose of the unit with the usual domestic refuse.
•  Do not burn the product.
•  Remove the batteries.
•  Dispose of the batteries according to the local statutory

requirements and not with the usual domestic refuse.

8.2.3 Environmental Disposal

Used products contain valuable material that can be harvested

and recycled.

Heat Pump Disposal

The Heat Pump must be dismantled and recycled by a

specialised service. The appliances must not under any

circumstances, be thrown out with household waste, or at

a general waste centre. At the end of its service life, please

contact an installer or local representative to proceed with its

dismantling and recycling.
When removing refrigerant from a system, either for servicing

or decommissioning, it is a legal requirement that all

refrigerants are removed safely.

The recovery equipment shall be in good working order

with a set of instructions concerning the equipment that is

at hand and shall be suitable for the recovery of flammable

refrigerants. In addition, a set of calibrated weighing scales

shall be available and in good working order. Hoses shall be

complete with leak free disconnect couplings and in good

condition. Before using the recovery machine, check that it is

in satisfactory working order, has been properly maintained

and that any associated electrical components are sealed to

prevent ignition in the event of a refrigerant release. Consult

manufacturer if in doubt.
The recovered refrigerant shall be returned to the refrigerant

supplier in the correct recovery cylinder, and the relevant

Waste Transfer Note completed. Do not mix refrigerants in

recovery units and especially not in cylinders.
If compressors or compressor oils are to be removed, ensure

that they have been evacuated to an acceptable level to make

certain that flammable refrigerant does not remain within the

lubricant. The evacuation process shall be carried out prior to

returning the compressor to the suppliers.

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды

Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание

Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды