Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ Скачать руководство пользователя страница 88

Страница: 88 / 94

Benchmark Checklist and Service Records

Installation and Maintenance

www.hhic.org.uk

* All installations in England and Wales must be notified to Local Authority Building Control (LABC) either directly or through a

Competent Persons Scheme. A Building Regulations Compliance Certificate will then be issued to the customer.

Issue date: 20.08.2020

ADDITIONAL SYSTEM INFORMATON (Tick the appropriate boxes/Measure and Record)

Water flow rate setting of the heat pump at commissioning (l/min):

Additional heat sources connected:

Gas Boiler

Oil Boiler

Electric Heater

Solar Thermal

Other:

ALL INSTALLATIONS

All electrical work complies with the appropriate Regulations

Yes

The heat pump and associated products have been installed and commissioned in accordance with the manufacturer’s instructions

Yes

The operation of the heat pump and system controls have been demonstrated to and understood by the customer

Yes

The manufacturer’s literature, including Benchmark Checklist and Service Record, has been explained and left with the customer

Yes

Commissioning Engineer’s signature:
Customer’s signature

(To confirm satisfactory demonstration and receipt of manufacturers’ literature)

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды

Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ, Установка и обслуживание

Результаты поиска

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ

Отзывы:

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренды по названию

Популярные бренды