Ideal Heating Logic Air DHW IDEPLUHP180DUOPPSZ Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 94

background image

INSP

& MAINT

63

Installation and Maintenance

Section 6 - Inspection and Maintenance

ᘐ

WARNING:

All maintenance and servicing tasks must be carried out by a competent and sufficiently qualified

engineer.
Work that requires the removal of the exterior casing of the Heat Pump must only be carried out by competent persons

who are familiar with the risks of R32 refrigerant.
Work on the refrigeration circuit must only be carried out by a Cat I or Cat II F-gas certified engineer.

Work on electrical systems must only be carried out by competent persons.
Refrigerant should never be released into the atmosphere. Refrigerant is to always be collected and recycled using a

suitable recycling unit.

6.1 OVERALL MAINTENANCE PLAN TABLE

ⓘ

IMPORTANT: Ideally, maintenance activities should be scheduled during times where there is little heating demand

to avoid disruption to the end user.

To keep the appliance operating as efficiently as possible the maintenance listed in

Table 14

should be conducted annually.

Failure to do so could affect the appliance warranty.

Table 14 Maintenance Tasks

Maintenance Task

Frequency

Heat Pump Inspection & Maintenance

1 year

DHW Cylinder Inspection & Maintenance

1 year

Control Box Inspection & Maintenance

1 year

System Inspection & Maintenance

1 year

Water Quality Treatment

1 year

«
...
61
62
63
64
65
...
»

Содержание Logic Air DHW IDEPLUHP180DUOPPSZ































































































Отзывы:

Нет отзывов

Похожие инструкции для Logic Air DHW IDEPLUHP180DUOPPSZ

Бренд: DAB Страницы: 39

Бренд: L.B. White Страницы: 99

Бренд: Samson Страницы: 8

Бренд: Unidare Страницы: 3

Бренд: Little Giant Страницы: 8

Бренд: VITAE Страницы: 72

Бренд: Lasko Страницы: 4

Бренд: EMI Страницы: 5

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: Argo Страницы: 10

TURBO-FLUX modular

Бренд: Cattani Страницы: 61

Бренд: N'oveen Страницы: 66

Бренд: W-Tec Страницы: 6

CTC EcoPart 400

Бренд: Regulus Страницы: 26

Бренд: Nectre Fireplaces Страницы: 10

Бренд: AQUASYSTEM Страницы: 12

Serve Better CP-RP

Бренд: Server Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды