Hyundai HI RUN n 700 Скачать руководство пользователя страница 27

Страница: 27 / 186

N700 Operating Instructions and Parts Manual

2. Installation and Wiring

(6) Mounting

Position

Mount the inverter in a vertical position using screws or bolts. The mounting surface should

also be free from vibration and can easily hold the weight of the inverter.

Fig. 2- 2 Mounting Position

(7) Ventilation within an Enclosure

If you are installing one or more inverters in an enclosure a ventilation fan should be installed.

Below is a guide to the positioning of the fan to take the airflow into consideration. The

positioning of inverter, cooling fans and air intake is very important.

If these positions are wrong, airflow around the inverter decreases and the temperature

surrounding the inverter will rise. So please make sure that the temperature around is within

the limit of the allowable range.

Fig. 2- 3 Ventilation within an Enclosure

(8) External cooling of inverter

It is possible to install the inverter so that the heatsink is outside of the back of the enclosure.

This method has two advantages, the cooling of the inverter is greatly increased and the size

of the enclosure will be smaller.

To install it with the heatsink outside of the enclosure, a metal fitting option is required to

ensure heat transfer. Do not install in a place where water, oil, mist, flour, and/or dust etc. can

come in contact with the inverter as there are cooling fans fitted to the heatsink.

Ventilation fan

Inverter

(Very good example)

(Poor example)

Ventilation fan

Inverter

(Good example)

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды

Hyundai HI RUN n 700, Инструкция по эксплуатации

Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды