Hyundai HI RUN n 700 Скачать руководство пользователя страница 19

Страница: 19 / 186

N700 Operating Instructions and Parts Manual

9.2.2

Multi-speed operation function (CF1~CF4)..................................................................... 89

9.2.3

Jogging driving (JOG : Jogging Operation) .................................................................... 90

9.2.4

Direct current braking (DB : External DC Braking) ......................................................... 91

9.2.5

Second control function (SET2) ...................................................................................... 91

9.2.6

Acceleration/ deceleration 2 (2CH) ................................................................................. 93

9.2.7

Three-Stages acceleration/deceleration (3CH)............................................................... 93

9.2.8

Free-Run Stop (FRS : Free-Run Stop)............................................................................ 94

9.2.9

External trip(EXT : External Trip) .................................................................................... 95

9.2.10

Unattended Start Prevention Function(USP : Unattended Start Prevention).................. 95

9.2.11

Software lock mode selection (SFT : Software Lock) ..................................................... 96

9.2.12

Analog input Voltage, electric current Transition [AT : Analog Signal Transition]............ 97

9.2.13

Reset (RESET) ............................................................................................................... 99

9.2.14

Wire(3-Wire) input function(STA,STP, F/R)..................................................................... 99

9.2.15

PID function selection and PIDC................................................................................... 100

9.2.16

UP/DOWN function(UP,DOWN,UDC)........................................................................... 100

9.2.17

Compulsion ON switching (OPE).................................................................................. 102

9.2.18

Torque limitation function (TL, TRQ1, TRQ2) ............................................................... 102

9.2.19

Multi-speed acceleration/deceleration time setting (XT1, XT2, XT3) ........................... 103

9.3

Analog order setting ................................................................................................................... 104

9.3.1

O-L terminal setting ....................................................................................................... 104

9.3.2

OI-L terminal setting ...................................................................................................... 105

9.3.3

O2-L terminal setting ..................................................................................................... 106

9.4

Other function............................................................................................................................. 107

9.4.1

Analog input filter .......................................................................................................... 107

10.

Explanation of O-group ........................................................................................................................ 108

10.1

Intelligent output terminal setting ............................................................................................... 108

10.1.1

Intelligent output terminal arrangement ........................................................................ 108

10.1.2

Wiring intelligent output terminals ................................................................................. 109

10.1.3

Output terminal function selection (o001~o004,o031~o032)........................................ 109

10.1.4

Output terminal contact (o005~o008,o033~o034) selection..........................................110

10.2

Intelligent output terminal function ..............................................................................................113

10.2.1

Signal during run(RUN)..................................................................................................113

10.2.2

Frequency arrival signal 1~5 (FA 1 ~ FA 5)....................................................................113

10.2.3

Overload advance notice signal (OL/OL2).....................................................................115

10.2.4

The Maximum PID Deviation Level (OD).......................................................................116

10.2.5

Alarm signal (ALM).........................................................................................................117

10.2.6

Over torque signal (OTQ) ..............................................................................................117

10.2.7

Instantaneous during power failure signal (IP) and trip voltage signal (UV) ..................117

10.2.8

Torque limit signal (TRQ) ...............................................................................................118

10.2.9

RUN time over (RNT) and ON time over (ONT) ............................................................118

10.2.10

Thermal warning signal (THM).......................................................................................118

10.2.11

Brake opening signal (BRK) and brake error signal (BER)............................................119

10.2.12

Zero speed detect signal(ZS).........................................................................................119

10.3

Monitor output signals (AM/AMI, FM) ........................................................................................ 120

10.3.1

Digital output signals (FM) selection (o009~o011)........................................................ 120

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды

Hyundai HI RUN n 700, Инструкция по эксплуатации

Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды