Hyundai HI RUN n 700 Скачать руководство пользователя страница 139

Страница: 139 / 186

N700 Operating Instructions and Parts Manual

10. Explanation of O-Group

118

(3) It is possible to use an output by assigning the signal 08(IP) during instantaneous stop, by

setting 09(UV) during under-voltage to an intelligent output terminal 11-14.

10.2.8

Torque limit signal (TRQ)

(1) When selecting the signal(TRQ) of Intelligent output selection, the signal 10(TRQ) of torque

limit is displayed.

(2) For setting the motor control method F012 to sensorless vector control(5), sensored vector

control(6), 0Hz domain sensored vector control(7), the output torque of a motor can be limited.

The torque limit signal displays that the state is limited.

Note) Please refer to 11.3 torque limit function (TL, TRQ1, TRQ2) for details.

10.2.9

RUN time over (RNT) and ON time over (ONT)

When the accumulated operation time reaches or is over the setting time in o028, RUN

time/power ON time over (TNT/ONT) output is switched.

Code

Function name

Initial value

Unit

Setting range

Contents

o028

RUN/ON time

over level

Hour

0~9999

Over time level setting

Table 10- 14 RUN/ON time over level

(1) RUN time over (RNT)

①

Assign 11(RNT) to an intelligent output terminal 11 ~ 14.

②

Set ON time level with o028.

(2) Power ON time over (ONT)]

①

Assign 12(ONT) to an intelligent output terminal 11 ~14.

②

Set ON time level with o028.

10.2.10 Thermal warning signal (THM)

(1) Set the inverter according to motor rated current to protect the motor from overloading,

overheating and damage. A warning signal is outputted before tripping on electronic thermal

protection and it’s level can be set in b029.

(2) Set thermal warning signal 13(THM) to intelligent output terminals 11~14(o001~o004).

Code
value

Function name

Output

statues

Contents

OFF

In case calculation value of electronic thermal is
smaller than the setting value.

THM
thermal warning
signal

In case calculation value of electronic thermal
exceeds the setting value.

Table 10- 15 Thermal(THM) warning signal

Note)

Refer to chapter 8.13 (Protection function for an electronic thermal) for details.

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Hyundai HI RUN n 700, Инструкция по эксплуатации, Страница: 139 / 186

Результаты поиска

Содержание HI RUN n 700

Отзывы: