Hyundai HI RUN n 700 Скачать руководство пользователя страница 160

Страница: 160 / 186

N700 Operating Instructions and Parts Manual

12. Explanation of H-Group

139

Status of running

Phenomena

Contents of adjustment

Adjusting

parameter

Speed fluctuation
is minus(-)

Set “Motor constant R2”bigger and bigger slowly
until 1.2 times for preset constant.

H004/H204
H010/H210

Driving

Speed fluctuation
is plus(+)

Set “Motor constant R2” smaller and smaller slowly
until 0.8 times for preset constant.

H004/H204
H010/H210

Set “Motor constant R1”bigger and bigger slowly
until 1.2 times for preset constant.

H003/H203
H009/H209

Regenerating

Lack of torque
at low frequency

Set “Motor constant Io” bigger and bigger slowly
until 1.3 times for preset constant. NOTE)

H006/H206
H012/H212

At starting

The shock is occurred
at starting

Set “Motor constant J” smaller for preset constant.

H007/H207
H013/H213

At deceleration

Unstable of motor
rotation

Set “Motor constant J” smaller for preset constant.

H007/H207
H013/H213

During torque limit

Insufficient torque
during
torque limit at low
speed

Set overload restriction level lower than torque limit
level.

b031
C007~C010

At low frequency
operation

Irregular of rotation

Set “Motor constant J” bigger for preset constant.

H007/H207
H013/H213

NOTE)

This case is that the motor control method (F012) was set as 4.

If the code F012 was set as 5, Io can be modified bia H008/H208/H014/H214.

Table 12- 4 Sensorless vector control (SLV)

12.4

Sensored vector control(V2)/0Hz-Sensored vector control(0Hz-V2)

(1) It is possible to realize precision and high torque by this function.

(2) Please set F012 to 6(V2) or 7(0Hz-V2) for this function.

(3) If programming the inverter for sensored vector use, It will need an encoder and a Feedback

Option Card for vector control function.

(4) Please refer to the feedback option card manual for this function.

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды

Hyundai HI RUN n 700, Инструкция по эксплуатации

Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды