Hyundai HI RUN n 700 Скачать руководство пользователя страница 74

Страница: 74 / 186

N700 Operating Instructions and Parts Manual

6. Explanation of F-Group Function

(2) Reduced torque characteristic (VP1.7 power)

This characteristic can be used when a large starting torque isn’t required.

At low speeds, it can cause the improvement of efficiency, low noise and low vibration

because of lowering the output voltage. V/f characteristic is as follows.

Section

ⓐ

: The limit from 0 to 10% of the base frequency is the constant characteristic.

(ex) If the base frequency is 60Hz, the limit from 0 to 6Hz is constant

characteristic.

Section

ⓑ

: The limit from 10% of the base frequency to the base frequency is reduced

torque characteristic. The voltage outputs in the curved of 1.7 power for the

frequency.

Section

ⓒ

: The voltage is constant from the base frequency to the maximum frequency.

(3) Reduced torque characteristic (VP2.0 power)

The voltage outputs in the curved of 2.0 power for the frequency.

(4) Free V/f setting

The free V/f setting represents optional V/f characteristics by setting the voltage and

frequency in seven parts. (A059~A072)

(5) Sensorless

vector

control

①

When this function is performed, raised torque running is possible at 0.5Hz above range

by the original torque control.

②

This function is the method that the revolution of motor and output torque are estimated

by output current, voltage of the inverter and motor constant of setting. It is possible to

operate with high starting torque and high accuracy at low frequency.

③

In the case of using this function, please select the suitable motor constant of using the

motor according to the parameter of "selection of motor constant".

④

If this inverter operates less than twice capacity for the maximum adopted motor, the full

⑤

performance may not be demonstrated.

Note)

Please refer to the part of sensorless vector control for details.

(6) Sensored vector control / 0Hz-Sensored vector control

①

It is possible to make a motor get the high efficient operation by motor speed signal.

②

Please use the feedback option card for using this function.

Note)

Please refer to the feedback option card manual for details.

Note)

Please set the carrier frequency (b010) as 2kHz or over 2kHz when use the motor

control mode(F012/F212) as 5,6,7.

6.11

Motor voltage selection (F013)

Please select the value of motor voltage to the nominal voltage of the motor, this value can be

found on the nameplate of the motor. If the motor voltage exceeds the nominal voltage of the

motor, there is a risk of damage to the motor.

Code

Function name

Initial value

Unit

Setting range

Contents

F013

Motor voltage selection

(the motor rated

voltage)

220

200/215/220/230

/240

200V(LF - model) : When

inverter is 200 V class,

selection is possible.

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды

Hyundai HI RUN n 700, Инструкция по эксплуатации

Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды